The Jalopy Journal
So I have 1955 Chevy Truck with a 235 straight-six and have had it for about 2 years like that. I use this truck as a daily driver (30 to 45min...
Runs great. Motor has been painted. Original motor and Trans. No rot. Just surface rust. Needs bed wood. Does not burn oil. Holds good compression...
1941 Chevy 216 Cubic Inch Engine. Stuck. Includes flywheel, bell housing, exhaust and intake manifolds, water pump. No carb. Engine code...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
1956 Chevy Bel Air two door sedan for sale. Very solid car[ATTACH] [ATTACH] [ATTACH] started as a gasser project. Fiberglass doghouse and...
I have a truck SHORT bed box for a 1954 - 1955 Chevrolet Truck. It has a nice patina and very little no cancer and is very straight. The tailgate...
I have 2- 1933 Chevy 3 window Eagle Series bodies, one is a complete car minus doors and decklid. Body #1 which is on the chassis is the one with...
[ATTACH] I picked this up a few years back as a spair, but need the space. The guy I got it from said it came out of a running driving car, so I...
[ATTACH] [ATTACH] Tin Woodie Project. Pretty much all there and comes with a later model 235 6 cylinder engine. Clean title and located right here...
Clean 1933 Chevy Pickup truck. Solid example of a California rust free truck and in great shape. Restoration has been started and some upgrades...
57 Olds/Pontiac Rearend, complete Bolt in TriFive Chevy Strange 35 spline spool/axles Fabcraft parts: 513 gear/Billet bearing cap/bearings and...
SOLD
THANKS
Nice shape, just don’t need anymore $80
Hey dudes I was wondering if you can help me out. I am putting a 350 in my poncho and was wondering if I can use the stock rad. I was curious if...
This engine was planned to be used in a project vehicle that has not developed; as a result, am selling. Bored .030 inch over; Jahn's pistons 194...
A set of PERFECT stock bench seat springs, doesn't include the frame. Had the whole thing sand blasted and powder coated gloss black before ended...
1928 Chevy Instrument Cluster . The speedo tested and was cleaned and lubricated. The amp meter and oil pressure gauge were cleaned up and...
Im new here on H.A.M.B. I restore vintage auto parts as a hobby. My full time job is the US Navy. I have a Vintage 1928 Chevrolet AC Automobile...
I got this bell housing adapter with a project. Need help identifying it. Casting is GM 2 #8826782. Chevy block pattern on one side....
So Im Looking To Drop My 62 C10. LWB It Is Currently A Torsion Bar Front. My Main Question Is How Low Can I Go In The Rear? Im Not Going To "C"...
I have a pair of 1958 Nomad's for sale. I have a title to one. The 283 in one of them will run off of a gas can. More than enough trim to build...
Some parts left over from a Gasser gone awry! Ford Sale: Offenshauser polished scoop - $150 Cal Custom scoop -$150 (see pictures not perfect)...
(((SOLD))) 1948 Stylemaster 2 door sedan Asking $12500 located in Dallas Tx. Straight 6 216 3 speed manual on the column duel exhaust Solid floors...
[ATTACH] Posting for my dad. 1939 Chevy Coupe Gasser Steel body, steel one piece tilt front end, 3 point roll bar. HiPo 327 out of a 1964...
Vacuum Advance Stud Type unit for Chevrolet 235 6 cylinder. Unit is brand new, opened box. Price is $50.00 +S/H Purchased from "Classic Parts...
Hi all, Not sure if I'm in the right forum for this but everyone here seems to be helpful anyway so here goes. This afternoon I noticed the...
I was told this spare tire cover would fit a 1940 1941 Packard. I'll let you guys out there decide for yourselves. It is in real solid condition,...
I have a Chevy Turbo 350 Transmission it came out of a 89 four wheel drive. How hard is it to change it over to a two wheel drive transmission?
Separate names with a comma.