The Jalopy Journal
After searching on line, It looks like everyone is using disc brakes, NOT I’m setting up ‘48 Lincoln bending brakes on a banger coupe. What kind...
Does anyone repopulated the Cragar “knockoff spinner” hubcaps that will fit 16” KH wires? Thanks
Changing from a Ford 12v generator, to a one-wire Ford alternator (Taurus). How do I make the wiring connections? Is the factory regulator used...
Have installed a Ford one-wire alternator in my 62 Falcon, originally a generator. There are three wires in the original harness, a heavy...
‘30 Ford coupe I’ve installed a reverse eye rear spring with several leaves removed to lower the back end. The frame is stock (not Z’d)(yet)....
ON my street engine, 7:1, 330 cam, Lion Head, header, single 97, Mallory dizzy. Setting a driveable ignition timing is frustrating. The curve...
Building a 30 coupe with reverse eye front spring, 4” drop axle, 37 spindles. Currently have a 1 3/4” drop steering arms. Tie rod has spherical...
Have a fresh banger short block, and a Graham supercharger. Has anybody adapted the Graham to the banger? Need some parts for the supercharger as...
Planning to build a banger for my 30 Coupe. Need a low pressure fuel pump for Stromberg carbs. Currently have a K&N 1-4psi pump, but tired of...
Working on a ‘34 Ford Pickup. The stock gas gauge is the hydrostatic gauge/sender. Doesn’t work. So, do I attempt to find an NOS sender and...
While recurving my Motorcraft dizzy, the retainer clip for the advance plate took flight. This is about 1/4” diameter with two vertical legs....
[ATTACH] Sun tach, 4 cylinder, 12v with proper transmitter box. Not tested, cant verify that it works, but could be converted. Both pieces in...
[ATTACH] [ATTACH] 39’ Ford, front backing plates. Bead blasted, with hardware shown. Planned to use on Banger project but went different...
[ATTACH] [ATTACH] Pair of 46-48 Ford backing plates. Great condition, bead blasted, buzz bomb black paint. New stainless steel sleeved wheel...
For my ‘30 banger powered coupe, I’m installing hydraulic brakes. The rears are the new Bendix Lincoln setup, fronts are ‘39 Ford, 12 x 2” Not...
I'm putting a list together for parts needed for a hydraulic brake setup for my 1930 banger powered project. When were brake cooling holes and/or...
Original bucket seats from a two door sedan. Will need complete rebuild/reupholstery Asking $200 OBO plus shipping. Prefer local pickup. Ken
Putting together a '30 Coupe, Banger powered, no fenders, etc. Considering using the stock steering, but need advice on what components I need to...
Working on the interior now. If I remove or narrow the shelf behind the seat, will the adjuster allow the seat to go back further. Trying to get a...
Just starting a new banger mobile project, 30 Coupe. Question, I have a 4" drop axle for the front, can I just remove a spring leaf in the rear to...
Great show, almost to large. Comments Ken
Getting started on a Track-T, banger powered roadster. Looking for info regarding frame rail material. Is 1 1/2 x 3 x .093 sufficient? 2 x 3 just...
Getting ready to install a rebuilt Straight 8 in our '48 Pontiac Streamliner. This car has a Hydramatic trans. Is there supposed to be a...
Reminder...... Northern Ohio Model A Club SWAP MEET Sunday, January 11th Medina County Fairgrounds, Ohio
Swap Meet.............Medina, Ohio.....Sunday, January 12th Medina Community Center Medina County Fairgrounds Doors open at 8:00 am...
'31 Ford Tudor, banger powered. Converted to '48 Lincoln Bendix setup last year. Pedal ratio at 7.5:1, 1" MC. Brakes work good, but am thinking...
<TABLE class=tborder border=0 cellSpacing=1 cellPadding=6 width="100%" align=center><TBODY><TR><TD class=tcat>Swap Meet, Medina,...
Changed my '31 Tudor (Banger powered) over to the '48 Lincoln Bendix brake system front and rear. Due to some linkage ratio issues, and thinking...
Has anyone used the "backup video" systems on their enclosed trailer? Any suggestions as too brand? Thanks ken
Changed my 31 Tudor (Banger powered) from mechanical brakes to the '48 Lincoln Bendix setup as sold by MACS. Originally used a 1" master, but...
Separate names with a comma.