The Jalopy Journal
As far as I know, this once great swap meet, traditionally held on July 4th weekend at the Western NC AG Center, has long been dead and buried for...
I’ve been having issues with what should be a relatively easy engine swap: SBC to a 41 Ford open drive trans in my 40 coupe. I researched this...
Can anybody ID this water temp sending unit? Has a stud and nut for an eye terminal. Goes to Classic Instruments Quad temp gauge like this. PO...
Looked at all the threads praising Odyssey 680 batteries but I still have a question. Also tried the Odyssey site (groan) Probably get one for the...
TOMORROW! Appalachian Fair Grounds Gray TN. Three buildings plus outside. Hit and miss on pre-48 parts. 100% RAIN FORECAST. [ATTACH]
I have an older Wayne compressor that has been a work horse for 15 plus years for me. Model 6885-SH, two cylinder, two stage. It’s running a 5 hp,...
I have a Carter M-2468 fuel pump going on the SBC that I’m putting in my 40. It supposedly is indexable to change the positions of the inlet and...
I’m having a senior moment.(again) There was a guy either on here, on FB, or IG that sold packages of printed shrink tube, with the circuit’s...
ANYBODY FIND ANYTHING…. [ATTACH]
I’m using a Chassis Engineering CP-2101 bolt in motor mount kit to install my SBC in my 40 Ford. (Yes, the one with the blown (up)flathead.)....
I have a pair of raw (still in black gel coat) Wescott rear fenders for my Brookville roadster. They have numerous (10-12) 1/4” and 3/8” holes...
*****SOLD. SOLD. SOLD*****
HELP! I’m having a very senior CRS moment, and can’t find the info for this guy. 40 Ford builder and parts dealer of some cool 40 pieces. Moved...
What say you SBC experts?? Freshly rebuilt ‘92 350 with what looks to me like a broken off dipstick tube. Did all the searches, tried multiple...
https://www.speedwaymotors.com/Speedmaster-1-229-011-168-Tooth-Billet-Flywheel-Chevy-350,323449.html Help please on the flywheel for my 40’s SBC...
I’m working on repairing an Edelbrock C4B for the SBC for my 40. It has three 5/16 carb mounting holes stripped, plus the two 3/8 water neck...
Made it to our club (KARC) run even without a car, so I worked the gate. Great location, cool weather, and 155 cars. Here’s few friendlies that...
I have a fresh rebuilt 350 with head casting 3998991 (70-76 307-350, 1.72 Int, 1.5 Exh). Acc. holes in the head And a set of fresh LOOSE heads...
I seem to remember someone on here posting years ago how they added stock outside door handles to either a smooth Brookville roadster door or...
Anyone on here bought a 32 roadster fiberglass dash from Speedy Bill? Did it fit? How’s the finish? Will it take the stock stainless oval trim?...
I’ve been trying for way too long to get my used 283 ready to swap in to my 40 coupe. It runs good, good oil pressure and compression, steady...
I’ve had this on the shelf for a number of years and now I’ thinking about using it in my recently traded for 32 Brookville roadster. The body...
********GONE*******
The windshield posts and frame that I got with my freshly acquired BV roadster are chopped 3”. I’m still in the trial and fit stage with the Wise...
As a couple of you may be aware, I satisfied my roadster lust by swapping my 32 Tudor body for a Brookville roadster body. Removed the sedan and...
I’ve had this almost full quart of this PPG/Ditzler DPE 1538 Zinc Chromate for a loooong time and it hasn’t solidified, changed color, or...
The biggest one ever at the new facility! Three buildings totally full and most of the outside. But nothing there. The increasing lack of...
Anybody go? It was today at the fairgrounds. Finally great weather and no plague, so the place was packed. Almost all the vendor spaces were...
Every time that I see a 32 roadster I get all woozy and start wishing and hoping that I had another hair blower (even with no hair). Some people...
[ATTACH]
Separate names with a comma.