The Jalopy Journal
1939 Ford Deluxe sedan. 23,000 trouble free miles in 3 seasons. Attended the 2016 Hot Rod Power Tour in Louisiana. Over 6,000 mile trip from...
40 Ford Standard hood. all metal work done and currently finished in black. Louvers are punched perfect. No hinges, trim, or latches. Contact me...
[ATTACH]Contact me through this site. I will look at all offers.
I have a 1939 Ford Deluxe sedan trunk handle that the lock can't be repaired locally. Anyone know where I can send it or find a working replacement?
Billetproof 2015 Washington. Looking for folks going up there from the Eugene, Oregon area that might want to travel together. Some of my regulars...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] I'm almost done with my second 39 Ford Deluxe grille, this time in...
What is the trick setup for wipers for a 39 Ford Deluxe Sedan with the original tilt out windshield? I tried Newport Engineering's setup but...
Hey guys, if you think building your own grille is something you don't want to tackle, think again.... it's rather easy if you get started right....
Ok you edelbrock carb guys.... I have a Edelbrock 1406 on my 330hp Chevy 350. I am experiencing some slight engine knocking at slight...
I'm looking at a fuel injection system for my 350 Chevy carbed engine. Who has used the FAST EFI system? What were your results? What were the...
Who out there has installed Specialty Windows power window kits in the doors and rear quarters in a 39 FORD tudor Sedan? I'm lookng for...
Ok guys, Does anyone make a re-pop of the '39 Ford Deluxe windshield cranks? I've been looking on different sites to find a good used one. Mine...
Has anyone had any experience with Phoenix Engines in Arizona. I am looking into buying one of their dyno'd Chevy 350 engine combination. What...
Hey Folks, is there a 'social group' on here for 39/40 Fords that is active? I just picked up a '39 Deluxe Sedan that is rust free and...
I ended up with a 64 Corvette four barrel manifold casting number 3799349 and a Carter carb that is dated to 63 Corvette number 3460S. Any...
Ok you 35 to 40 Ford owners.... what width rear end (either 8 inch or 9 inch) are you using with rear parallel springs. Tell me where you are...
Wow!!! What a show they put on! I think around 600 cars and perfect weather for the event. The unofficial "cruise" on friday night and again on...
Anyone know the latest laws reguarding front license plates and fender use in Oregon? I've seen many rods running without them and wonder if they...
Ok guys, I'm looking for someone that can tune my two Holley 94's used as primaries on my Ford 300 six. I live in the Eugene, Oregon area but...
Just got this running and it hauls butt. '83 Ford 300 block, Clifford dual four manifold adapted to use two Holley 94's with mild cam, manual...
I'm installing two Holley 94's with a Clifford manifold on a Ford 300 six. I have a stock vacuum advance distributor currently on it....
Can anyone find out what my Ford 300 six came out of? The casting number found on the passenger side of the block reads; E 1TE 6015 AA. It came...
Check this recent shed find!!! No way I'm telling where this one is! This is mine! I hope i loaded up the pictures correctly...
I'm thinking of using a Ford 240/300 six cylinder Marine Manifold on my yard art rod. Can anyone give me a picture or a manufacture for this? When...
Has anyone else out there used Jamco Suspension for their ride? I just put a complete Jamco suspension system front and rear on my 53 Ford... I...
I've had a few rod guys give me their thoughts on fish plating frame rails. I'm doing a cruiser Yard Art Rod with a six cylinder and three...
Ok guys.... think back and see if you can identfy this body for me. I have no pictures of the cowl just the door on back. [email protected]
Anyone know where I can get a bottom pan for a Model A radiator? Does someone make one for retail? Any help would be appreciated. [email protected]...
Has anyone tried Demon's new 98 carbs yet? I'm thinking of using three of them on my Ford inline 6 (one primary and two secondaries). I would...
Finally got time to get on here. I've read many of the posting but never found the time to repond or offer an opinion... but finally I'm here....
Separate names with a comma.