The Jalopy Journal
dodgedog91, welcome to the forum. You struck a cord with me about the 354 you acquired. I have two 1958 Dodge truck 354 hemis and a 1958 Dodge...
Could we get a little info on your vise seen in the photos?
This is my 354 hemi 2x1 intake for my 1958 Dodge D400. On this particular setup you can see the governor arm that would attach to a governor...
Welcome from California. Can't wait to see that 354 hemi 2x1 intake in use. I'll be using the same setup for my Dodge truck. What are the serial...
Can't resist this thread. Went past 143 in my '94 RX7 when I quit looking at the speedo and still could feel the car accelerating. I finely beat...
Now that's a good lookin intake. Steve [IMG]
Stude, I may part with one but they both need to be completely redone. I did a search for instrument repairs and found a few links on the H.A.M.B....
I couldn't help myself. I found the gentlemans number, called him, made the deal and now I have another 1958 Dodge truck 354 hemi. :D Did I...
Stude, my 354 distributor does not have the mechanical tach drive any more. So my plan is to have the tach rebuilt with electronics. The rev meter...
This tach came from a 1958 Dodge D700 with a 354 hemi. It's mechanical with an hour meter or rev counter, not sure. This will be added to my '58...
By the way, I really like the idea of shaving the back of the bellhousing off and replacing with what I need. Do we still have the good ole boys...
If I read that right, trading a gallon of swish. The last time I did that was in the Philipines when I needed a serial number for my '50 Panhead...
The transmission bolt pattern of your bell and my '58 bell are the same. Since I'll be using a 354 hemi for my 1958 Dodge truck the idea is to use...
By looking at the rear bellhousing mounts to the frame cross member you have a 1959 Dodge truck engine. Although, I am thrown by the ID number....
I apologize for not getting back to you sooner. My avatar is a 1958 Dodge D400 1-1/2 ton dually. It happen to have a 129" wheelbase which was just...
Thanks for the pic. I was quite surprised to see dual oil bath air cleaners. That does look sharp. The possiblities!
Clark, would you post a pic of the 2x1 air clearners. I've got the same intake for my 1958 Dodge D400 1-1/2 ton and have never seen the filter...
I like the Dodge truck in the back ground in the first pic. I've already got five of them and I'm drooling over this one. I need a shrink!
I have a 1958 truck 354 hemi but the Power Giant stickers have worn off and I wish I could get them replaced. If somebody doesn't like their Power...
Hey Al, I'd really like to see a pic of your set up. I was going to incorporate the same manifold on my 354 for my 1958 Dodge D400 but was...
That is a beautiful 1957 Dodge D500 or D600. I recently bought a 1958 Dodge D400 with a 129 inch wheel base which is the same as the 1 ton Dodge...
Hey Stude, I'll be moving my 354 hemi off the trailer in Sacramento that morning. Getting ready to pick up my most recent purchase in Iowa during...
Well, Adams 1959 Dodge poly 318 is finding a nice new home in my 1959 Dodge W300. The truck has the stock flat head six and 4 spd. After the 318...
55 Dude, that's a really interesting '57 Dodge. Dodge didn't come out with a W300 (1 ton) until 1958. I was thinking W500 but the fenders don't...
I'll start with singles and see how that pans out. I'd rather go duals but I would have to cut the inside fender well/box out to clear the inside...
I appreciate the feed back, guys. I have the 2bbl manifold on the engine right now and wanted to change over to a single 4bbl manifold. The dual...
I'm new to the hemi world and have recently purchased a 1958 Dodge 315 hemi and a 1958 Dodge 354 hemi. As you can see in the pic of the 354 in...
I showed this to my wife. Now she appreciates my 315 hemi. We both laughed so hard.
I'm rebuilding a 1958 Dodge D400 1-1/2 ton. It has a 315 poly soon to be replaced with a 1958 Dodge D700 354 hemi. I have a 9 foot utiline box...
Separate names with a comma.