The Jalopy Journal
Volvo box I bought for my shoebox but never used. Its tight and complete as pictured. Shipping is from Houston Tx and shipping price is actual...
216 isn't the best engine. If it runs just keep running it. If you like the straight 6, get a 235. They are very cheap or free. Sent from my HTC...
Scam. Also the wording of the message is strange. Sent from my HTC One M9 using The H.A.M.B. mobile app
Don't clear it. The clear will harden and the oil will not be able to evaporate the vapors Sent from my HTC One M9 using The H.A.M.B. mobile app
What do you want it to do if you get low oil pressure? Horn, kill the engine etc. Sent from my HTC One M9 using The H.A.M.B. mobile app
Limited panels? What are you needed that you don't see? Between EMS and others you should be covered. Sent from my HTC One M9 using The H.A.M.B....
Where is voltage stopping? Sent from my HTC One M9 using The H.A.M.B. mobile app
HF guns w disposable cups. Sent from my HTC One M9 using The H.A.M.B. mobile app
Stop air from getting in the tank (block vent and inlet) and the lack of air displacement will allow you to remove the filter and replace it...
What is his labor rate? I would think about 16 hours if inner rockers, floor braces and everything else was OK. Sent from my HTC One M9 using The...
The scaredy cats? Sent from my HTC One M9 using The H.A.M.B. mobile app
The hole is there to prevent a sudden surge of coolant and the engine cooling off too much. By allowing a small amount to go by the engine will...
The fastest way to find something is to go buy another one. Sent from my iPhone using The H.A.M.B. mobile app
Just a update since I hate reading threads that are never updated. Before I removed my intake I checked the torque for the heck of it...found...
I brought this up a few years ago and received a lukewarm welcome. Still...putting on a show like that is ALOT of work, and no event is ever...
ok...lets end this thread. I am going to order another/correct power valve and use this opportunity to remove the manifold, heads and paint the...
I removed the power valve and found it marked 14...is that 1.4? For some reason I remember to divide by two, which would be about...
ok I stand corrected...the other times I had pv failure, it would leak enough that the bottom of the intake was wet with fuel. I will remove this...
blown power valves will allow gas to leak thru over night...there is no leak.
[IMG] So I checked the pv overnight and no leak...so I wanted to see the value, and nothing on the valve...but I see a brass jet that is...
A resistor converts voltage to heat. Resistor size is directionally proportional to heat it gives off. I know that doesn't answer your exact...
Thanks for the ideas everyone...I am going to call the company I bought the carb from on Monday and ask for the specs and the ok to disassemble it.
Yes I know about the power valve. No it didn't backfire. The tank is venting. There are no leaks. I pressurized the tank w air with soapy water on...
running straight pipes...currently disconnected about a foot past the exhaust headers. I am going to blow thru the mixture screws in a second.
Nothing traumatic happened....well, 6 months ago the throttle caught in the open position and the engine revved a bit high but shut it down and...
Thanks pope...I was thinking that also so I used a heat gun to check temps and they were heating evenly on all cyl. Did it run super rich and...
I think the carb also...funny thing is I put the old carb on and it did the same thing...but is the vacuum opening the power valve, and bypassing...
ok thanks...small powervalve? When I say a new carb, I mean I just put it on yesterday and the company is closed today so I cant get the specs....
Yes I have searched and no one asks direct questions so hard to decipher a answer. 49 Ford flathead, 80lbs compression plus or minus 15 %, new hei...
Apply for a lost title and go from there. No one is going to authenticate signatures.
Separate names with a comma.