The Jalopy Journal
Model A engine that does turn over. No markings on pistons other than a prick punch to show what bore they go in. Valve chamber has little...
Model B engine with the CB crank that has the weights sweated on. Does turn over. I can not see any cracks in the deck but it does have minor...
Free 1956 olds 324 block. Bare block with major pitting in two of the rear cylinders. Standard bore so maybe possible to bore to 4 inch and save...
I just achieved the brake in miles on an Olds engine so time to change the oil. Pulled the oil breather cap and noticed there was part of the...
These heads and intake came off a 303 olds that was bored to 324. They have the better 1.8 rockers. No problems that I can see. Intake is a 4...
I bought this for the #10 heads but they needed more work then I expected. Block is seized. Heads have been cleaned and checked for cracks but are...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] Block is a 239 inch sleeved with standard pistons. No cracks that I can see but does have issues....
Hildebrant starter crossover for 49 to 56 olds. Missing small piece at the one locating pin. Also has had one thread repair with heli coil. Minor...
Model A or B side drive magneto mount. This is a raw casting that needs machined. Price is $45.00 plus shipping . I take PayPal friends or USPS...
Older casting of a Riley two port unmachined intake for Winfield carbs. Could also be used for A/B flathead but the mounting flange will need to...
Lower input shaft for open drive Halibrand quick change. New never used. Does show signs of shelf wear. Total length is 17 3/4 inches. Six splines...
[ATTACH] [ATTACH] Nice clean book with jacket. No markings inside that I saw. One of the first books by Don Montgomery. This one was printed in...
Cam driven oil pump pulled off a B engine. Timing cover looks to have mount brazed on. Pump was using one inlet from pan and two returns. One...
Aftermarket water pump marked Bergs. These are usually found on T's but this one came off a B engine. Shaft turns but is tight. Missing one grease...
Prestolite magneto with mount that has not been used in at least 10 years. I spun the shaft slowly and I don't see a spark. Points were not...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] Mallory tach drive dist. from a MGB that if modified will fit a Model A or B. There was an article in Secrets...
A complete SR BB downdraft with Winfield intake that I used on my roadster. Ran fine but I would suggest it be gone through. I know the float...
Three are complete with EE 7/8 base. One of these is damaged with the inlet busted off and a small hole drilled in the float cover. The other one...
1962 NOS Stewart Warner 5000 rpm mechanical tach and two NOS 2 to 1 tach drives. Also included is a new 63 inch cable. One of the drives has had a...
Winfield SR BB Updraft. Carb is missing linkage and choke horn. Will need rebuilt or use for parts. Price is $275 plus shipping. [ATTACH][ATTACH]
Cast Aluminum Stanchions, were used but don't show much wear. Look like they could easily be chopped if wanted. Asking $60 plus shipping. Email me...
I bought this for my roadster but it doesn't work out and I have found out it is a 37 Packard wheel. The dia. of the wheel is 18 1/2 inches. Rim...
Here is a roadster top that I picked up a Model A auction. After I got it home I found out it does not look like any of the Model A tops. I have...
I have a complete 1946 1.5 truck chassis for sale. It has a 158 inch wheelbase Model 698T I believe. Was an old farm platform truck. Comes with 7...
This pair of seats came with my Model A project. I am not going to use them but before I put them up for sale I would like to know what they came...
I have a pair of Delco-lovejoy shocks that I am trying to disassemble. I can't seem to be able to remove the seal cover or cam arm. Is the seal...
Has anyone ever replaced the ball on a wishbone. I have a 32 wishbone and the ball could use some repair but I was wondering if anyone ever just...
These were in a bunch of Model A stuff I purchased. Can anyone ID them for me. Their aluminum with a Dia. of 12 1/2 inches and the recessed depth...
Been lurking for awhile and its those monthly Banger meetings that called me out. Up to this point I've only been playing with motorcycles but I...
Separate names with a comma.