The Jalopy Journal
[ATTACH] [ATTACH] 150 obo plus shipping, Hurst 2nd style for side mount a Pontiac engine to a biscuit mount. Holes have been opened up for a large...
I have a pair of M/T wheels i would like to remove all the rust before i have the fronts bead blasted. I was thinking of soaking in a water and...
4.10 is sold . Have 3.08 posi. Olds 31 spline axles , 55" housing Complete housing , has been swapped to 31 spline axles and posi center section...
Sold
I have 2 complete rear ends from 64 Pontiac. One is a 3:08 posi, other is open unsure of gear. Open rear 600, posi 1000. Will not ship. 64 is a...
200 obo for 2 wheels plus shipping. Us postal money order only[ATTACH]
600 plus shipping for a nice pair of slots. 4 3/4 only, not unilug. New centercaps includes also[ATTACH] [ATTACH] [ATTACH]
For a cheap paint job like a rustoleum job without the hazards of the chemicals to spray. Has anyone tried something like this ? Wondering about...
***********sold*********** Very nice set of tires with i'd say 90% tread, has stepped whitewall. These are 8 years old according to dot but no...
I'm trying to get a better brake pedel out of my set up. It's 4wl manual disc brakes. gm intermediate calipers on front and explorer calipers on...
*************SOLD*************** Fairly solid 2dr sedan for sale. Original 316/hydramatic. condition of engine unknown, haven't had time to mess...
Here it is my next project. It's all stock and if I can get it going probably will leave this one that way. If not I have a newer Pontiac...
I have a pair of doors for sale. they both need some work on the lower portion of the skins. One just needs straightened with a stud welder/puller...
Std bore block ans std size crank. block will need bored for rebuild. I have the old rods and pistons if you want to reuse the rods but will all...
2 wheels and tires for sale plus the special lugnuts required , they are 7/16" thread. Gorilla lugnuts has these if you need 1/2". They have the...
*********************SOLD******************************* I have a complete running 75 Pontiac 400 from carb to oil pan. Newer plug wires, milage...
2 decent wheels . 50 plus shipping for both. Can bring to Meltdown drags in Byron. One has a small amount of curb rash in one area, the other had...
I did a simple search for " Pontiac" and 20 of the first 30 results were the same thread? There was another one listed 3 or 4 times also in the...
I picked up a set of these and trying to find the proper lugnuts. The ET II wheels are the round 5 spoke center that are in a steel wheel shell ....
I have a decent pair I had to cut up and move some tubes on one side. Any powder coaters on here? Do these need to be stripped to have redone or...
I picked up these Cal Customs for my engine build. I'm trying to decide if breathers or twist in caps would look better . I had some chrome...
I have a rusty pair i'm debating putting on the front of my gasser. My Cragars are gone so looking for other options and I have these . I...
This mostly pertains to spraying clear over a Rustoleum type paint job. I was in at the local farm store and saw they offer a clear to go over...
I picked this up the other day to get a few of my heads done. Black and Decker " Vibro-centric" kit. It's pretty complete with the stone...
I have a rear 1/4 spear I had in a 2" pvp pipe and still managed to get bent. Can I put a little or any heat at all to help straighten it out?...
This is the 2nd year for this event, last year only a fall race. Now one spring and one fall. There was a pretty good turnout last year and should...
I'm looking to upgrade my brothers 454. Right now flat top pistons (.030 over)and 781 open chambered heads which are rated at 113 cc. I have...
Is there a decent place to find this book online? I'd like a copy and searched on Amazon and it's either around 100 or over 700:eek:. I've added...
I've been looking at seat covers online, mostly finding expensive reproduction covers. I've seen covers listed at Kanter, but don't know of their...
I've having some issues trying to find a hose to fit what I need. The mount is right in the way for a normal looking hose. What type of pipe would...
Separate names with a comma.