The Jalopy Journal
Ok I'm trying this again in a diff forum since my last post got deleted and the moderator never PM'd me back.... I have a master/slave...
I was looking through the GNRS thread last night and noticed that all the customs (or kustoms as some folks call them) seem to have the same...
Hey everyone, I had to remove the front timing cover from my ford 302 Windsor engine. I got it off fine and went to reinstall it, and noticed...
I ran new 3/8" stainless steel fuel lines along the inner left framerail of my '54 ford. It also has rubber fuel line hose over a few of the...
I'm running the fuel system on my 54 ford which has a 1968 302 ford engine swapped in, and I'm pretty clueless about a lot of this. On my fuel...
So I have a 1954 ford which I've swapped a mild carbureted 302 into. This is pretty much the first time I've done a custom swap of this size, and...
So my project of swapping a 302 into my 1954 ford has reached the point where I need to put some exhaust on this thing. Now due to my lack of...
Hey I pulled a motor out of a '71 chevelle today and I was wondering if you guys could tell me any information on the engine from the casting...
Hey has anyone here run malloroy (sp?) ignition in their car? I'm thinking of picking up a kit from summit that has a distributor, ignition box,...
Hey everyone, I'm swapping a 1968 302 from a fairlane and a T-5 trans. from an '88 mustang gt, into my 1954 ford. However, I need to change the...
Hey everybody im doing a '68 302/'88t-5 swap in my '54 ford and i figured I'd put up some progress pics to see what you guys think. please excuse...
Hey Im swapping out my eng. and trans this week and i just bought my clutch and flywheel from "RAM clutches" for my new engine. The eng. and...
anyone know the size of the motor mount bolts that go into the block on a 1968 windsor block?
Hey everybody Im trying to put a 302 and a t-5 in my 1954 ford. The problem is I have a '68 ford fairlane 302 and the t-5 is from an '88 mustang....
Im building a '68 ford 302 out of a failane and My engine builder gave me an oil pump from melling and a pickup tube to go with it. the problem is...
Im rebuiliding a 302 right now and im attempting to put the water pump on. The casting # says the engine is out of a 1968 Ford Fairlane but I went...
Hey I'm putting a 1968 ford 302 out of a fairlane in my 1954 ford sedan. Anyways, I had the motor rebuilt with a basically stock rebuild with new...
I have a 1968 ford 302 out of a fairlane thats going to go in my project. I'm getting some head work done (porting, cleaning, new valve springs)....
I have a '68 Ford 302 out of a Fairlane. It's mostly complete and I have it pretty much completely disassembled at this point. I'm thinking of...
I have a 1968 ford 302 out of a fairlane that I'm rebuilding to put into my '54 ford. I'm currently disassembling the engine so I can get it to a...
Well a few weeks ago I posted about how the 223" inline 6 in my '54 ford has been running rough. Changed the spark plugs and oil, still no help....
I have a 223" straight 6 in my 54 ford. It's been converted to 12 volt electricity. It's getting replaced by a 302 soon but for now i need it to...
I bought an engine earlier this year that I know very little about. So far, from talking here on the hamb I've been told it's a 1968 ford 302,...
Hey guys i bought a cheap ass engine stand for a 1968 ford 302 that I'm rebuilding and It didnt come with a bolt kit. I called summit and asked...
anybody have pics from the summer nationals in worcester, mass last weekend? I wanted to go but couldnt make it. I hear it's a pretty crazy show.
I found an engine I want to buy today but I dont know much about it so I thought you guys could help.... -It's a small block ford engine, either...
I have to write an essay on how to channel a 32 ford with fenders 3 inches. I basically need every single little detail i can find about the...
where can i find blueprints for a front engine dragster chassis? I go to wyotech and am thinking about building one instead of building my project...
hey i just rebuilt the original master cylinder on my 1954 ford. It's the stock-type single piston m.c. but I didnt bench bleed it before putting...
ok this is probably a very stupid sounding question, but I have a 54 ford with an oil bath air cleaner on a 223" inline 6 cylinder engine. I want...
Separate names with a comma.