The Jalopy Journal
I bought the Phosphoric prep and etch yesterday and I had mixed results. Half the places went down to clean metal and the other half seem...
Most of the frame is already down to bare metal. I don’t think POR 15 will adhere. I have heard some people really like POR 15, but I don’t...
I have a few thousand dollars in parts, but those were purchased when I had the extra money. I’m a 27 year old dad and work full time. I already...
I don’t have much money to put into it right now, but I have a lot of parts and time to mess with it. Sent from my iPhone using H.A.M.B.
I appreciate the reply. I actually have a really small portable sandblaster and an air compressor, but I live in a neighborhood and want to try...
I bought Van Sickle tractor and implement paint and primer. I don’t care about it being show quality but I do want the metal to be protected and...
I’m building a 56 F-100 and have it tore down to the bare frame. I have hit the frame with a wire wheel on the outside, but the inside of the...
I just stripped everything off my 56 F-100 frame and am considering having it sandblasted. Does anyone know of any hole in the wall shops that do...
Okay, I’ll just use some RTV on it. Thanks guys. Sent from my iPhone using H.A.M.B.
I have looked all over and cannot find the correct axle housing flange gasket for my Ford 9” big bearing old style flange. It’s the one that is...
What is the difference between the 9569 and 9568? Sent from my iPhone using H.A.M.B.
I have been to my local parts stores and they seem to have little to no knowledge when it comes to parts. Sent from my iPhone using H.A.M.B.
No offense but I did google it and I am seeing different people say different numbers fit. I just wanted to make sure I get the right thing....
I have a Ford 9" rear axle out of a 1964 F100 which has the sealed bearings and 28 splines. Does anyone know the correct part number for the axle...
Okay. If I go ahead and replace all the bearings and seals and do them myself what all will I need? Sent from my iPhone using H.A.M.B.
I just half assed clean the gear up to take the measurements. The red on the gear is old fluid and was caked on everything. I didn't see any...
[IMG][IMG] Sent from my iPhone using The H.A.M.B. mobile app
My buddy is an electric motor mechanic and he brought over his dial indicator. We measured three different teeth around the ring and two were at...
I am hoping I can get by without disassembling the third member. Sent from my iPhone using H.A.M.B.
This axle was pulled from a complete truck by the previous owner, so it hasn't been sitting outside on the ground at least. I'll try brake...
Thanks guys, I guess tomorrow I'll start disassembling and cleaning it. Once the axles and differential is removed, what type of product is best...
I just picked up a complete Ford 9" rear axle complete from drum to drum. What can be checked with it out of a vehicle to see if the axle...
That's kinda what I'm thinking. It would be cool to keep the 3 on the tree, but with the engine swap and all it probably would be better on the...
Would it be better to just go with a floor shifter? Sent from my iPhone using H.A.M.B.
The impression I had kind of gotten from trying to research this was it had to have the linkage on the side for the three on the tree. If that's...
Perfect, that's exactly what I wanted to know. Thank you! Sent from my iPhone using H.A.M.B.
I think I want to go with a 351W in my 56 F100, but am not sure what transmission will do what I want though. Is there a 3 speed transmission...
It's been in my family since 1957. Sent from my iPhone using H.A.M.B.
Thanks guys for the responses. I will get the mechanical side of the truck squared away then take y'all advice on how to attack the rust and...
I've read a couple guys have used CLR and scotchbrite pads and then use Gibbs oil rubbed over the entire body once it's smooth. Does that stuff...
Separate names with a comma.