The Jalopy Journal
I'm mocking up a 1931 Model A and at this time no SBC. I'd like to get the distance from the center of the Motor mount to the front of the WP...
Locking ignition coil from what I can find fits a 1933-40 Chevy (possibly other GM cars of that era). Coil itself is stamped DelcoRemy 538-7. I've...
Banjo type steering wheel, non-Ford and a splined shaft. 18" diameter 3/4" splined mount and offset bent spokes. The wheel doesn't have any...
[ATTACH] Squarebird hood Rust free (some light surface rust. Measures 54" wide 57" length and approx. 8" tall to the top of the scoop. Will not...
Searched here, Summit, Jeg's, Fastenal, and Grainger. Struck out on all of them. I need two lengths of aluminum hex 1" OD and 3/8" ID so I can...
Did a search and found references to it but no picture. I remember seeing a picture of it on the one of the drag cars threads. The search came up...
Just pulled these of a 327 I'm selling. I put this together in 1973 and took it out of my 31 A Town Sedan in 1976. It's been sitting in dry...
I bought these as part of a 31 Model A roadster body package back in the early 1980's. They are in excellent condition. If not 31 Model A then...
Probably 30 years ago I purchased a 30 Roadster body that had been restored with rear 1/4 panels that were graphed with coupe 1/4 panels below the...
Not a run of the mill pan but not a trap door pan. Surface rust inside but solid otherwise. Is it worth de-rusting (vinegar) or is it just scrap....
Selling a 327 Casting code 3858174 Block pad stamp is FI12T8HE Cast L145 (1965). Had it in a 31A Slant window Sedan for about 4 years and removed...
I sold the original Tach drive generator and want to convert to a Mallory Tach drive distributor. So what are the ratio's from a Gen. drive and a...
I've known Paul's family since 1970 when he was maybe 7 years old. His dad and Burns Barryman started the Early Irons Street Rod Club (in Warren...
All plus shipping from Brookings Or 97415 57 new repro Pass. taillight housing $ 100 57 trim piece above the taillight $ 80 Gas...
I did a search on "axle shaft length" here and struck out all the dissuasion was about housing width. I'm looking specifically for the axle...
Really solid Pontiac 2 Dr. sedan Complete less the rear bustle trunk lid. No rust anywhere that I could see when the local scrap yard owner...
Got all of these for free from the scrap yard before they got crushed. The smallest (green)is just a case The largest is really stuck and only...
I'm trying to figure out if they are Standard Roadster or Deluxe. The 1975 wood kit from Byron Meyers in Wichita Kansas has Deluxe Roadster listed...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] 351C Holley Street Dominator 4V intake. Cleaned and top blasted. This is for the...
These were sanded to 1000 grit then polished. They are not a show finish but will be ok on a driver. There is corrosion on each VC that I can't...
Under car headers from an original 289 Cobra. (helped take them off) No dents, thin spots from rust and all slip joints are good. 1-3/4 primary...
I'm planning to sell a set of headers from a 1964 Cobra and would like to know if they would clear the OUTSIDE of an A frame. Looks like they...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] What appears to be a BBC oil pan (I'm not a Chevy owner). Picked this up along with a BBC blower manifold and...
I've been thinking of this for a while but what time frame were " PASSENGER CAR V8 Engines built" Ford Flathead...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [/ATTACH] [ATTACH] [ATTACH] All prices plus shipping from Zipcode 97415 Ramshorn Exhaust manifolds from 1962...
[ATTACH] [ATTACH] Front 2 doors from what I can tell a 1954 Olds 4 door sedan. (they could be 1953) Rust free and none or very few dents. I hauled...
The cover has 3" ID fine threads that seal the bearings. Just want to know what it would fit. I've got 2 of them, gave the 3rd to a shop owner...
I've installed a 9" rear axle with 4 bars and the original cross spring in my 48 Continental. I'm keeping the original 12" front Bendix brake...
Never installed lower shaft for a Champ type quick change. 10 spline front and rear, overall length is just over 19-1/2 inches (19-9/16). Front...
2 dr HT original Owner 73K miles 283 V-8 auto trans. My sister-in-law's husbands aunt has the car and she is not able to live alone (90+ and...
Separate names with a comma.