The Jalopy Journal
Any idea how to watch Iron Trap live on Sunday??? Are they still filming on Sunday"s???
Does Hop Up have monthly print subscription. I received my annual and would love to have a monthly as well.
Thinking about buying a lathe. Tips, shortfall. I have my eye on a 6" Atlas Cratsman metal lathe 101.07301. How hard are metal cutting blades to...
what flywheel and pressure plate do you use when mating a SBC ( 350 in this case as I already own it) to 39 Ford manual trans. The Ford one or the...
Sure wish you would offer embroidered sew on patches in your merch. Iwould like a few for my shirts and levi vest.
Have a stuck front brake drum that is the Ford wide five configuration. Any suggestions on a wheel puller for it. I want attach to the studs in at...
How do you remove the entire floor in a 39 Deluxe Coupe. I have a complete donor floor that I would like to replace it with.
Dos anyone know of a manufacturer that sells a gantry that is 96" inside dimension between posts. Most max out at 94". Need to get a car off my...
Thinking of going with AR torque thrust wheels on my AV8. the only 16" ones I find are 8" wide. Are 5" wide wheels available?? I have 6:00 16' on...
have a relealy nice denim short sleeve jacket that I would like to sow on clothe patches too. Are these available.
Have a set of Red's headers on my AV8. They measure 1 5/8 OD 1 1/2 ID. I would like to weld a flange on the end so I can have a spot to break it...
Getting close to doing some plumbing on the AV 8. I am using F-1 front brakes, 39 rear brakes an F-1 cross member with F-1 pedals and an F-1...
Just starting to teach myself how to tig weld. So far I really like it but have a question. Is there a guideline that is used for selecting the...
OK I thought I had this thing licked but have come up with a problem. I did the Tardell suggested installation of an F1 steering box in an A frame...
Going to try my hand at TIG welding after years of MIG. I got the basics down I think but I would like to know what you guys are using to sharpen...
Need to upgrade my torches. Looking for advice on what is the best on the market right now. seems everything comes from abroad. My use is...
Life has been good to me lately and it looks like I might have the funds to invest into a 2 post or 4 post lift for my garage. My problem is that...
Anyone go to the Invasion yesterday??? I have been going for the last five years but the change to a 10:00AM spectator entrance time deep sixed it...
Going to have to put an offset in this pitman arm. About a 1/2" minimum maybe more like 3/4". Need to do it to clear my split Model A wishbone....
OK you guys have been a lot help. Final question on this I hope. When putting the box back together using Tardells little book about it I have run...
Anyone know where I can find the star washer on an F-1 steering box that locks in the adjustment. Mine is missing. Should I be thinking about red...
Anyone have an idea where I can get a reamer or a honer for F-1 steering box sector bushings???? Welded a Model A flange to an F-1 box per...
[ATTACH] Does this look right to you guys or should the shoulder on the clutch shaft be flush with the transmission case. It's a new clutch shaft...
Took me a little while to even consider posting this here because it's pretty embarrassing. Finally came to grips with it and thought maybe I...
[ATTACH] [ATTACH] What do you guys think. Should I just re-[ATTACH] [ATTACH] bush and use or start looking for a new shaft. It's going to be in an...
Been trying to find out if there are any rules that must be followed to compete in the hill climb. Went all over their website and can't find any....
Getting to the point of getting my steering worked out on my AV8. I am using a lowered A axle (3.5") reversed eye model A spring with F-1 backing...
Finally getting around to setting up the steering on my AV8 project. I have 46 48 spindles in a3.5 dropped A axle. I am using an F-1 box in the...
1000HP from a steam engine built in 1941. It came thru our little town and I was lucky enough to get a shot of it. Don't think it burns coal...
Just received my exhaust headers from Red's for my AV8 and to tell you the truth they are beautiful. I really don't want them to rust and I don't...
Separate names with a comma.