The Jalopy Journal
The transmission was connected to a flathead I bought. I was just curious if it was a decent transmission, and worthwhile keeping around.
Thanks a bunch, any experience with these transmissions?
[ATTACH] Hey everyone, picked up a flathead/transmission, out of a 53 Merc pickup. What exactly is this transmission? I'm guessing T87 but not...
I am planning one of these in a 36 sedan behind a SBC. Still working out the details. Posted using the Full Custom H.A.M.B. App!
I'm curious if it would be worth while to do some small parts from Canada. Chrome plating is expensive up here too, maybe even more so. Not sure...
Well whatever you do, preserve that 8 ball! Sounds fantastic!
1-3/8" small stem pinion (aka. '741') Carrier casting numbers: 1820657 (1957-1964), There we go. 8 3/4 Dodge 57-64.
Thanks for the nudge in the right direction. I think it is a 8 3/4 Dodge rear end. I am going out today to measure the bolt pattern and turn it...
I was hoping it would have had a tag or something on it. I ran those numbers but no dice.
Came across rear end, no tags, only numbers are the ones shown. Any ideas? [ATTACH] [ATTACH] [ATTACH] Posted using the Full Custom H.A.M.B. App!
He figured it was a 28, but wasn't sure. He said he doesn't want much for it, I am going back to buy 2 rifles, so maybe if I give him asking...
Found this today at a wild boar farm, the guy said make an offer, think it is worth while? Motor and trans are in it, doors and other bits and...
Thats what I wanted to hear. I noticed you are in Alberta, where abouts?
My plan was to get one of those Chassis Engineering mounts, maybe for a TH350 so I can split my wishbone, then mod it to work with the NV3500....
Still good info. What did you do for a rear trans mount, I have beed searching the net for what will work, without much luck. I understand that...
Alright, with a bit of research, here is the quick way to tell the difference between 290's/5LM60's and NV3500's, from Fullsize Chevy.com....
I think, from a bit of googling that you can take off the shifter tower and see the one shift rod for an NV3500 and the 4 shift rods for the...
What pedal set up did you use?
Well $350 for everything, I might still roll the dice on it. I'll just drain the fluid there and see what pours out. Even if it is one of the...
I wish I could get a new one for under $1000! Not up here though.
Yes, been to both those pages, the second page there lumps the NV3500 and it's predecessors all into one listing, but from what I read, the...
Hey all, I have a line on a transmission for my 36, it is about 2 hours away. The fellow emailed me some pictures of it, but none of the tags...
I gave up on accepting deposits, it usually turned into some crazy 6 month layaway plan.
You don't get more specific than that. Thanks man.
Cool, I have no rims yet, so that should be no problem, I figure 3/4 of an inch on each side should be no problem for clearance. RB35, are you...
Hey all, in my hunt for a 75-80 Granada rear end for my 36 Sedan, a guy emailed me this morning with an 8" rear end out of a 75 Comet. I have...
Ah, but do you tell the seller which bearing is burnt out in the motor just by smelling that dip stick? You may as well stick the dipstick in...
Hey, just wondering who makes a good rebuild kit for 36 steering boxes. I can find step by step instructions on line but not a complete parts...
Subscribed for interest. This is my issue I am concerned about in the 36 I am building. Not for keeping warm, just defogging during warm muggy...
I am heading to the city (Edmonton) in 2 days, going to find a wishbone out of a 37 or up to split and use the CE trans mount/wishbone splitting...
Separate names with a comma.
The Jalopy Journal
