The Jalopy Journal
Thanks for the info , it has been very helpful . I'll try to let you know how it turns out.
I will check their site . I am going to try to find a hot rod shop near me and see what or who they recommend . I'm sure there is one somewhere...
In that case , I need to know how to adjust the caster on a Mustang 2 front end . Seeing how the crossmember is welded in place , Is that...
I have a 1926 Essex 3 window coupe . My question is about the front end alignment . It has a Mustang II front end and for the most part , it...
There is a cool old copper dash emblem on my coupe that is within reach of both driver and passenger . I removed the emblem and mounted a...
Thanks for the reminder . I forgot about that . Is the bell housing bolt pattern the same on pre 1987 and and the later small blocks ?
I finished up th 26 coupe about 500 miles ago and while it's good to drive and all , it's missing something . I wish I wouldn't have gotten in a...
Thanks guys . I'll try it first thing in the morning .
Remove the windshield frame from the windshield on my coupe ? It's a chrome frame like speedway sells and the glass needs replaced . I have no...
Same here . Have done coil springs with no problems.
Thanks guys . Sach's and CR Lawrence both have exactly what I need . Sach's actually sells the CR Lawrence stuff . I knew I would get the info on...
JC Whitney said they don't have it but they'll check around .For now I'm still looking unless or until they come through . I'm sure this size...
It's for a 1926 Essex 3 window coupe that the doors/window channels no longer resemble anything close to original . I'll check with JC Whitney . I...
Window channel felt ? Any dealers on the HAMB ? I found one place on the web , restoration specialties , but $110 per 96" piece :eek: seems a bit...
Thanks a lot guys . Looks like I'm making a fuel tank ! I always get great advice here from guys that know what they are talking about .Joe, I'll...
I don't have access to a tig or a brake so there would be more welded seams than I would like and they would be mig welded . In your experienced...
I am wondering how difficult it is to make a fuel cell/tank ? I looked in the tech archives and didn't come up with any . Has anybody done it ? I...
There's none I can see . There are no wires , just the posts sticking out .
I have an 8,000 rpm Stewart Warner Tach and can't figure out how to wire it . It has a baby blue plastic housing and three threaded posts sticking...
I could make it exposed from the bottom , I can see if it ruptured it would leak out and not in , might also expose it to road debris flying up...
You're all right . I was just trying to be lazy . Thanks for the reality check !
Due to the lack of anyplace else to put it , the fuel cell in my Essex 3 window coupe is going just behind the seats . It's a factory made ( Jaz I...
There's a 60 Chevy sitting on a trailer in Branson West , Mo along side of Hiway 13 . Don't know if it's for sale or not . Might be a better...
I just did this on my Ford 9". I don't know if it's the cheapest , but it sure was simple . I ordered evrything from a place called Quick...
Let there be light ! I'm 59 years and my eye sight ain't the best either . After making sure what you are going to weld is clean , hit it with a...
I drove up and looked at what the guy said he thought was a 1932 Plymouth coupe . I don't know much about the different old bodies but I feel...
I stumbled across a guy that has a 32 Plymouth 5 window coupe body . It doesn't have any doors or a deck lid . I've only seen a picture of it but...
I have an old rearend I was told is out of a late 50s-early 60s Ford . I pulled the brakes off and measured them at 11"X2 1/4" . Went to the local...
Separate names with a comma.