The Jalopy Journal
here ya go. I think they’re about 1,000 cheaper on eBay, through speedways ebay store....
I know I’d have to swap the motor mounts, it comes with a th350 mount, which would work with my S T-10
I know it looks fine the way it is, but every time I see a 27 on 32 rails I wish I did the same. I have to pull the body off to mess with some...
I always do that, forgive my stupidity, 1932 frame made for a 1927.
Been searching all over for info regarding this frame. It’s from speedway, it’s the 32 frame that’s built for a 27 roadster. Just curious if...
Sorry I'm revisiting this old thread, just looking for some opinions. Ideally, notching the rear subframe for more clearance with the diff would...
EOIC - Exhaust opening, Intake closing. Turn the crank until the exhaust valve starts opening, then set the intake lash. Turn the crank until the...
Also, are there any other 331 guys out there that know a little something about the head gaskets. Between cylinders 2&4,6&8, 1&3 and 5&7, right...
Ive been around a few hemis for a couple years, and I've seen the tin and aluminum ones used. My uncle likes the aluminum ones, my other uncle...
Thanks, hopefully the other tubes get here before the weekend and I can put this issue to rest
I'm familiar with the little bit of oil that seeps when you remove the plugs, but this is more than that. I measured out how long of a tube I will...
Ya I have seals at the valve cover, just wanted to see if this oil leak made sense to someone besides me, since there wasn't a seal at the plug...
I have a 1954 331 hemi that was given to me by my very generous uncle, along with a 1927 roadster, all original Henry Ford steel. The motor was...
I've got a 27 model t roadster, original Henry Ford steel. I'm not sure what you call the rear portion of the body that the turtle deck sits on,...
Thanks for the input. I know I'm not using the wrong gaskets. I've chased and followed that passage way 20 times with and without the Gasket on...
Ya I'm not sure what's going on, something has to be missing at the nozzle assembly though. Right now it's the brass screw with crush washer,...
Ya I pretty much did everything you guys mentioned. Replaced umbrella, nozzle is on the right way, tried multiple accelerator pumps. It is a very...
The first accelerator pump wasn't bad, but I figured I'd replace it anyways with the rebuild kit. I have 2 rebuild kits, plus the old accelerator...
i have a road demon 625, all was well until I had to replace the needle and seat, so I did a basic rebuild with new gaskets and all. The...
Thanks Ray. So I'd assume that if the motor was rebuilt that long ago then it wouldn't be the anaerobic sealer I'm seeing? If it only stays wet...
So it's normal for them to leak after a couple hours of idle time? I would have thought when the rebuilder did the break in the motor would have...
It's definitely oil, smells like oil. Can't tell you what it taste like though. Allergies have been bad lately, so it was only a hint of oil smell...
Ok I was hoping it had to be some kind of sealer. Why would the freeze plugs start leaking all of a sudden and at once? From sitting too long?
It doesn't look anything like rust, and wouldn't I have seen a trace of red when I drained the oil? This was the first time the oil has been...
1954 331, rebuilt by a reputable shop about a year and a half ago and stored until recently. Never been on the road, just started and tuned in the...
Finally put some bias plys on, makes it look like a different car
They actually just called back and confirmed you can't use an ISO free hardener with the regular 2k primer I kinda knew the answer to my own...
Ah sorry about that.. Custom shop 2k primer/sealer kup-405 Custom shop ISO free hardener kfp-306
I was just about to spray some 2k primer, reduced to use as a light sealer coat over epoxy primer. I just realized they gave me an ISO free...
Ya the hole saws I use are nothing special, I think they're milwaukee, I just get em at the local hardware store. Trick is low speed, pressure and...
Separate names with a comma.