The Jalopy Journal
Take a ride this week end to one of local tracks , MIR MD 35 ish miles Cecil County Md 30 ish Mason Dixon Md /Pa 30 ish Summerduck Va 60...
On the Bug & other sizes you can make a cup & install on inside behind Butterfly to cut down / lesson CFMs & still be functional,,, The only...
post #6 looks to be a Hillborn with mods to set on a Carb ...Time was spent on Butterfly's.....May be some one did One off modifying the Original...
pic of converter looks correct , when converter is slid all the way back to the pump typically 1/8 to 1/4 gap ..... A """153 tooth""" flexplate /...
Just Enderle Bug with or with out Rib & block Val for Gas , Alky , or Nitro , (K) [ATTACH]
First post pic ,Looks to be Enderle bug with ribs , more likely so!! Late 60s to present , or you can get with out ribs [ATTACH] [ATTACH]
I Never seen one's sold with out being kustom built
The adaptor that slides under the rotor button should have 8 slots / windows Or 8 magnets , when you have # 1 piston on TDC , tip of Rotor...
Typical USA models coupes Others will add more details or look up dealer sales brochures for each year model 28-29 Narrow curved cowl...
Hhmmm , I will Bite !! On a Bier Street , neither car down the Lanes , 1/8 mile , 1 burn out . State wide lanes with lines. Also some where you...
There is already a situation like this that popped up here a year ago! ( Thread) If I recall correctly one in the Midwest the other one in the east
Thumbs Up!!
All So , R -J new location around 30 air miles away Will be looking for as soon as first post says This was in mail box today #86 [ATTACH]
The idler pulley, in my experience running it on the downside didn't work out too well,,, have you ran it in the past that way?
SS tube nuts or make your own Solid rivets out of SS Polish,, look into Aviation/Aerospace
^^^^^^^^^ That Looks to be a Channeled Body with a Major Rear Kick up after the rear of door
I'm only familiar with Fords,, ""Pre War "" Fords body Do Not have a S# ,,,, Only the frame , A FoMoCo Title/Vin # is for Frame , Engine ,...
Im sure in 2007 it had the Radiator cap
^^^^^^^ NHRA or IHRA on line Rule Book There are None Sanctioning tracks Run what you Brung
Thinking H R D also , I also do not have a compleat set of R J
Triangular No pan bar needed Exhaust needs and cures [ATTACH]
^^^^^^ same [ATTACH]
Close fit & needs mocked up like others have said, with blower 3:71-6-:71 , Belt drive & fan If you plain to mount radiator in stock location ,...
Yep , needs to be welded , I would like to know the reasoning for maybe somebody was experimenting on a dyno
No , my mounts are in the typical location , as used in Pete & Jakes , On 32 with SBC
Small cut & removed @ bottom of Firewall under The distributor to clear peek of block & transmission. On passenger side firewall was cut and...
If you are dealing with your compression ratio 10-11:1 , you can run on good stock engine & parts 3-4 psi under full boost @ full throttle 5,000...
So Not Duplicating /Match side to side, Trying to make each side Look Identical ,,, I'm sure the Dan Olsen I have are same side to side , the...
Not trying to be a Smart A$$ Unbolt driver side Bolt header flang together easier to duplicate on a table[
The museum that is non-racing is amazing, The ones that do stop in if you're really interested in automotive & American history plan on spending...
Separate names with a comma.
The Jalopy Journal
