The Jalopy Journal
Mike, Ill get back to you on the fax/e-mail thing I've got several articles you might find useful. got to beg the wife into showing me hoe to use...
You will never match the performance/economics of the smallblock chevy, BUT, the cool factor of the six cannot be denied. One of the greatest...
I remember when Moutain Dew first came out. They had the hillbillys on the bottle, cost ten cents, I drank a lot of them. Sure a different image...
I have a 2.5L AMC in my 90 Jeep Wrangler that I woulnt trade for any other engine in a jeep. I would love to run one these in my T-bucket. Ive...
Its not so bad really. The head was already cracked and if it were'nt for a BIG rear main leak I might have tried just puttin on a new head. As it...
Sure makes you wonder.
Yea its ok to laugh cause I bought a 6 cyl, 4 door. This car reminds me SO much of high school and all the stuff we did with (to?) our cars. Most...
Mine's a driver so its only about 3 inches lower than stock. The old Butches Rod Shop had a whole suspension kit.Front and rear lowering blocks,...
I bought a 55 Chevy, four door, six cyl., manual. Solid body and it ran pretty good but it wouldnt start unless you dribbled a little gas down the...
Does anyone know what the stock rear end ratio for a 55 chevy sedan, 6 cyl, 3 spd manual, NO overdrive???
Ive got three. A baja- helluva lotta fun off-road, a sedan, thats lifted, for daily driving in these $2.00+ a gallon gas days and a volksrod...
An old Car Craft mag from to seventies showed me how to bend an old intake valve 90 deg. stick the stem in bellhousing hole and lip in flywheel...
InPrimer, thanks. I should have done a search first. That sounds perfect for me.
Thanks, most helpful.
Ive always heard sand blasting ports ect. was bad because the pores in the cast iron trap little particles that are almost impossible to remove...
Im not familiar with the flamethrower. The larger gap used with longer reach plugs allows the arc to get farther away from the combustion chamber...
I want to use a pre EGR intake to replace the smog manifold on a sbc. I figure I can tape of the ports ect and sand blast the top side but what...
Are you talking 'just the column' and not the steering box, cause the shaft is one piece. That cinch bracket at the bottom just holds the sleeve...
For those of us out in the boonies wheres the best place to order parts (ign., carbs, gaskets, ect) from. Anyone to stay away from?
Ignitor I or Ignitor II? I understand the Ign. II has about a 5 sec delay in starting while it powers up. It also will shut itself down if you...
Cool, thanks.
Ray, A man of few words. I like that but could you flesh it out a little? Have you run this combo or known someone who has? Any pitfalls?
Thanks Ryan, I love this board but I dont post that much. I guess its because I was raised " If you dont have something positive to contribute...
I have a petronix unit in my delco dist. can I also use the MSD-6? I like the easy starting/ increased fuel economy of the petronix but I would...
Its a good place if you dont weaken
Mortuary supply? I would have never thought of that. You guys continue to amaze me! Thanks. I dont live in Phx so no phone book but I do go down...
BTT Thanks Lady.
Cool, that will work, although whenever I go to Harbor Freight I tend to end up with a lotta shit I didnt know I needed. Anywhere else?
Does anybody in PHX or surrounding areas know where to buy blast media for a blast cabinet? Im not looking for a truck load just a hundred pounds...
I always thought it would be tits to put one in a Jeep. Im sure its been done but Ive never seen one. A flatfender or a CJ5 would be bitchin.
Separate names with a comma.