The Jalopy Journal
I have a brand new Mallory ford flathead Electronic Distributor that never been out of the box. I’m ditching a flathead project and selling all...
So this master fits 1967-76 Corvette and 69-70 Chevelle and I did find some instructions. I believe that the "front" of this master is the round...
I am in the process of installing a new dual drum/drum master for my 59 chevy truck. I have it mounted up in the stock location under the floor...
I'm looking for a little topcoat advice. I sprayed my roof this weekend with some Zero-rust red oxide primer, which came out really nice. I also...
I've put a 76' Maverick rear in my 53' ford, now the center wheel hole/flange doesn't fit over the end of the axle. I want to keep the stock...
I have the cable from the handbrake lever back to about the transmission. The rest didn't come with the car.
I have a 76' Maverick rear end in my 53' Ford. I'm putting the rear drum brakes in now. My question is will one those Lokar(or anybrand) emergency...
Found in the desert, just wondering what it is? Anyone know? [ATTACH]
Freshly sandblasted metal is not exactly "clean" metal. If you have ever TIG welded anything after being freshly sandblasted you will notice that...
I'm getting ready to mount the body back on the frame of my 53' Ford. The body mount kit is around $150, which seems a bit high for some rubber...
For hinge pin's try Tom at http://www.ccrod.com/home.htm. He's really helpful and knows his stuff when it comes to hinge pins. I had a hard to...
Does anyone sell lowered steering arms for 1953 Ford's? I see them for Chevy's but having a hard time finding them for Fords.
I need some advice on what specifically I can do to minimize bump stop while lowering my steering safely. What I have is a 53 Ford with stock...
I do want to strip the paint and just polish them up. So it sounds like chemicals are going to leave spots on them. Sanding is going to be...
I have some aluminum valve covers that I want to strip the paint off of. Is Aircraft stripper the best way? Pretty sure sandblasting is a no-no on...
I think the problem with taking any roof off has to do with the doors. The roof is tying the 2 sides of the car together and by taking it off you...
Your have to go with a open driveline with a PG. Like 49ratfink said, the turbo 350 is the way to go. Early Camaro's rear ends fit for these cars...
Thanks a lot, that's exactly what I needed.
I am considering putting a 54' Chevy 2door post body on a 4door frame. Anyone done this here? Was the frame and the mounting points the same on...
Anyone know the answer to this one?
I put a 69' Camaro rear in my 1949' Chevy 3100. You will have to grind off the old mounts and put new one's on. I think the dimensions for what...
I am putting a rear end from a 74' Maverick in my car. It's from a junkyard and didn't have any brake parts on it. I can't seem to find a diagram...
Landshark - Fang
I have a Ford 8 inch rear that just had new bearings pressed on. Before I install the axles do I need to pack the bearings? They look to be...
I have ordered from them, they seem ok. They seem to specialize in selling small parts for a little too much money, but they do ship quick and...
I didn't know where they were located. Thanks, thats what I needed.
Trying to find a parts dealer with the name of "Rare Parts"? As you might imagine, a google search brings back a little more than I want. Need...
I've got a Ford 8 inch rear from a 76' Maverick. How do you drain the fluid in this thing? Do I have to siphon it out from the fill plug? Bottom...
You can also get that slide chart from Lincoln which will give you all this info based on the material and thickness you are welding. They are a...
3/32" tungsten, ground to a sharp point on a tungsten only grinding wheel with grind going parallel with the rod. The point lenght should be 2.5...
Separate names with a comma.