Register now to get rid of these ads!

RichFox's Recent Activity

  1. RichFox replied to the thread Hot Rods FAST, CHEAP AND RELIABLE.

    Exactly what I was going to say. I have had a 460 Ford and a 455 Pontiac in a small, light non HAMB friendly car. Not at the same time....

    Feb 20, 2018 at 2:56 PM
  2. RichFox replied to the thread Hot Rods 427 Fe high riser Blower ??.

    If you wanted to do that, I have run an Electromotive distributorless ignition. Reluctor wheel on the crank hub and a pick up. Really...

    Feb 20, 2018 at 2:38 PM
  3. RichFox attached a file to the thread Hot Rods 427 Fe high riser Blower ??.

    This is a dual distributor drive i made, but it could be an offset drive just as well. I used three gears from the Boston Gear catalog....

    !cid_3DD3AB4E-A126-4286-AE24-06CCE07275A7.jpg Feb 20, 2018 at 1:52 PM
  4. RichFox replied to the thread History Comp Coupes, All but forgotten?.

    I remember an early HRM with a picture of a V8-60 powered Bantam coupe. Said it was the only street driven CC at the Nationals that year...

    Feb 19, 2018 at 10:06 AM
  5. RichFox attached a file to the thread Lets see pictures of cars that were channeled and left not chopped.

    OK see if I can post my 32 this time.[ATTACH]

    05_2421.JPG Feb 18, 2018 at 5:00 PM
  6. RichFox replied to the thread Technical 331 Cadillac build question.

    I measured the ID of an Earls -4 adapter at about .200 inch. So that would be an area of ..031 inch. Not much. If you don't want to do...

    Feb 18, 2018 at 11:19 AM
  7. RichFox replied to the thread 80's 6.6L ford motor good for anything?.

    In '77 I bought a new Ford F100 with a 351M and C6. Primarily to pull my race car around. And over some pretty big hills between here...

    Feb 18, 2018 at 10:13 AM
  8. RichFox replied to the thread Technical 331 Cadillac build question.

    Very hard. I think I would consider seeing how much clearance you have with the existing bolt hole. Calculate the area of that...

    Feb 17, 2018 at 11:12 PM
  9. RichFox replied to the thread 80's 6.6L ford motor good for anything?.

    It will bolt to a C6 or a top loader. Should be enough.

    Feb 17, 2018 at 11:05 PM
  10. RichFox replied to the thread Technical Crankshaft oil plugs.

    Our local NAPA store has a large selection of soft plugs. Maybe yours does to.

    Feb 17, 2018 at 11:03 PM
  11. RichFox replied to the thread Projects technical can anyone identify this distributor ..

    What you have was pretty much the hot set up on Traditional fast cars before it was Tradition.

    Feb 17, 2018 at 5:34 PM
  12. RichFox replied to the thread 80's 6.6L ford motor good for anything?.

    400 cubic inches and Cleveland heads fit. How can this thing be bad? Any idea what we would have thought of one of these in '59?

    Feb 17, 2018 at 2:18 PM
  13. RichFox replied to the thread Technical 331 Cadillac build question.

    i understand where he is coming from. That is the easy answer. But all the OEM bolts are cut smaller in the body. What is the tensile...

    Feb 17, 2018 at 9:58 AM
  14. RichFox replied to the thread Hot Rods XO/PP Bonneville project.

    I don't know how pickups get all this neat stuff. Roadsters sure don't.

    Feb 16, 2018 at 7:45 PM
  15. RichFox replied to the thread Technical 331 Cadillac build question.

    Good. I thought they would have what you needed. If you want I will relieve the end bolts for you. You pay shipping

    Feb 16, 2018 at 7:42 PM
Register now to get rid of these ads!

Archive

Copyright © 1995-2013 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.