The Jalopy Journal
Has anyone here used Medford Speed & Machine in Vincentown, NJ? I stopped in there today and talked to Jerry. Really nice guy, knew his stuff,...
Sorry gents, this is a hot rod site, not that kind of stripper. Anyways, I picked up a new cab recently and began to strip the old prime and rust...
See descriptions below. Also open to REASONABLE offers. Prices do not include shipping and will be leaving from 08022. Let me know if you have...
Two brand spanking new Quick Fuel Slayer Series 600 cfm carbs. I bought them to put on my tunnel ram, but they will not fit because they have...
Eelco panel with Sun 8500 RPM tach and EB9A transmitter. Also a Sun fuel and amp gauge are included. Overall nice piece but does have some...
Hey guys, Getting ready to paint the rear end housing in my truck. I put some cheap red oxide primer on it when I first welded everything up just...
Superior Glass Works, stock width, smooth running boards. These were purchased brand new 3 years ago and only mocked up on jack stands, never...
Original, solid GM steel. They will need some metal working to make them perfect, but in very nice shape overall. $60 plus the ride. [IMG]...
Open carrier for a 9.3 Pontiac/Olds rear. Gears are original GM 2.69. Just the gears and carrier, no case. No pictures at the moment, but can get...
Setting up a Pontiac Olds 9.3. This is the best pattern I've gotten, however, I have .058" of a shim pack. Is that too much? Does the pattern...
Open carrier for a 9.3 Pontiac/Olds rear. Gears are original GM 2.69. Just the gears and carrier, no case. No pictures at the moment, but can...
Set of headlights for a '41-'46 GM Truck. They are pretty rough, but still salvageable. Check the photos and you can see the bondo and rot....
Edelbrock Victor Jr. for SBC. Has a small repair by the right front carb stud, but is in otherwise good condition. Never grinded on for gasket...
Edelbrock Torker II intake for SBC. In very good shape, but will need a good cleaning or bead blasting. $50. E-mail ([email protected]) or PM me...
Stock front axle out of 1938 Chevrolet 1/2 ton truck. All steering and brake components included, but no leaf springs. Axle is the same basic...
'55-'64 GM passenger car rearend. Open third member with 3.55:1 gears (I have to double check this, but that is what the tag indicated), yoke...
So I disassembled my 1964 Olds Eaton posi unit for inspection and cleaning and a possible rebuild. Turns out it is all like new and just needs to...
Morning all, I'll be ordering some tires next week for my build. I'm going with 9" Towel City tires, but I can't decide between the pie crust...
Hi guys, I have a set of chevy steering arms that I need reamed for 7 degree tie rod ends. I don't want to spend $80 or more on a reamer I will...
Two questions: 1. I'm going to be installing the lower front shock mounts into my front axle soon. My plan is to use some 3/4" O.D. chromemoly...
I had my truck sitting at what I thought I wanted the ride height to be and set the engine level at the carb pad. Now that I have been able to...
So, I feel as though I should probably contribute a little more to this place than I have. So I'm going to do a build thread...reluctantly....
I know that my motor-plate is not exactly traditional, but it fits what I plan to do with my truck and where it will be going in the future. It's...
Got the rear suspension all tacked in finally. Still need to get a longer diagonal link and I plan on adding some plates to the ends of the upper...
I have searched and searched and can't find an answer I am reasonably happy with. I am currently working on the rear suspension in my '38 Chevy...
I know the internet is the least of our problems right now, but is anyone else seem to be having a problem receiving messages over the internet...
I'm pretty convinced that I want to run the early 60's IHC brake/clutch master cylinder on my truck. I have all the specifics worked out and...
Contrary to what everyone says, it is not impossible to title a vehicle in NJ. I've been in possession of my '38 Chevy truck for 15 years and had...
I have a '38 Chevy 1/2 ton with a boxed original frame, using only the original front and rear crossmembers. I am running an engine plate and...
Separate names with a comma.