The Jalopy Journal
I built a fabricated quickchange. http://www.jalopyjournal.com/forum/showthread.php?t=415472 I had at least a solid week building it. If you...
Go to weldingweb.com They have a pretty active classified section and you might find something in your area.
That's not what you want. That's basically the same circuit they use in all the cheap narrow band O2 gauges. A wideband controller has some...
You will be surprised to find out how far off you are when you think you have a well tuned carb. I have a TechEdge which will data log and also...
Two words of caution when you get one. Never leave it in the exhaust pipe without the controller connected and powered up. Leaded gas will...
Found this really cool turboed Y block when cruising the Megasquirt forum. http://www.msextra.com/forums/viewtopic.php?f=104&t=46823
Guess its kinda like the dumb asses that do the same things to cars.
My son is the crew chief on the Precious Metal P51 Mustang.
I put an O-ring on mine and have had no leakage problems. I think I would use six bolts like a Halibrand cover. You have to figure that the bolts...
Lucked out on that one. I had to spend $300 for some cut to length axles.
When I made mine I machined all the bearing bores after I had welded it. this eliminated all the distortion problems. Must have worked pretty...
That is pretty much how I did it on my homemade quickchange. If I recall, I turned down the shoulders on the side gears so I wouldn't have to...
Where do you live in Johnson Co. I live in Goldsboro and if you run out of options, I may be able to help you out.
There is a Jones 2:1 right angle drive on E-Bay for 27.85 + shipping. Item # 251007555072.
Taper the rails down to 2" for about 30" and us a 2" crossmember. Just looks better
There's a 2to1 right angle tach drive on E-Bay for 24.85....
Another thing is if your welder has a water solenoid, don't use it. Just plumb it for constant flow. If the solenoid goes bad you will burn up a...
Get some real plug wires..
Keep every receipt. It really helps when you get a bonded title. I did mine in NC and it is a little bit of a hassle but not as bad as I thought....
Done it a million times. Use tig and stainless rod. For real small tacks I use stainless safety wire for rod.
I installed some Model A spindles on a tube axle the same way that you did, including the needle bearing. Have about 600 miles on it and seems to...
They aren't bad if you run a hood, but in a hoodless car they look like crap because they leave a big gap between the square radiator top and the...
Go to an electronics supply store and get some aluminum hex standoffs. They make them in various lengths and thread sizes. I doubt if they have...
Heres a Toyota 3TC I have in my T roadster. It was originally a 2TC which is 1600cc, but i put a 3TC crank in it and made it an 1800cc. It has an...
At one time Sun made an HEI adapter for them. I don't know if they are still available. I'm sure someone like GMC Bubba would have the answer....
Which part is bad, the sender or the gauge. I would try to find out what the specs are for the sensor and check it with a good thermometer and an...
if you search on Ebay for a dc to dc convertor they have a ton of them listed and they are only about 10 to 15 dollars. they will take up to...
The only problem I see with removing the bushings after they are chromed is that when you push them out it is going to peel the chrome off the top...
That is how I built mine. Got a repop Halibrand rear cover from Speedway and a lower shaft and worked backwards from there. Actually, the bottom...
I think your 45K and the turbo is what jacked it up. I have a T roadster with a four cyl insured for 20K and payed 287.00 for the same coverage...
Separate names with a comma.