The Jalopy Journal
Its the same piston that came out. Cylinder wasnt machined, only cross hatched to seat new rings then I found the issue, still STD. If all goes...
Looking at white.papers on a wet lined V12 cylinder temperature study reveals some meaty data. Water cooled cylinder wall temperature rarely...
what about this stuff, wonder if it would stick....Its a fire rated putty but comes in a 4oz syringe so I think its still served up liquid....
Im gonna JB 1 82 Mazda B2000 cylinder. I have a 2mm x 2mm by maybe .002 deep (if that) as I can feel it but its like how a cleaned rust spot would...
This is awesome! Could I use this schematic to drive a generic ma meter? I have an old Equus engine analyzer who's tach function does not work, it...
It was against a 351W powered Ford, not a Cleveland mill.
The import ECU's have a substandard transistor under that 'cap'. If the transistor on top has no name on it (ST or Motorola, etc) and is held on...
https://worldradiohistory.com/hd2/IDX-Consumer/Archive-Poptronics-IDX/IDX/70s/74/Poptronics-1974-09-OCR-Page-0017.pdf
If your gonna zap it with electolysis, use washing soda, not baking soda. Washing soda is available in the detergent section and looks like a big...
put a sanding belt as wide as the journals on a drill around a sanding drum, sand side in or out. rotate the crank against the sanding belt slowly...
Sure, they will rebuild/service for $129 a pair or offer you $75 credit for something else. They would nto rebuild mine for free. Bummer because...
John, In any 2 or 4bbl holley rebuild kit, there are some teflon strips that not many people know what to do with. These are shaft bushings...
put a light spring and a sealing ball bearing in another 2 part filter.
Whats more embarrassing than your ride overheating at the car cruise? Having it piss all over the car in front of you in line to get into the car...
just remember, fuel in air doesn't like to turn sharp corners as the heavier fuel likes to keep going in its original direction while the less...
Does this count? Slant six TR made from 1.75 EMT and a cast valve cover! EFI of course and the injectors are going into the HEAD, epoxied right...
Packard 4.1:1
Ok, maybe I should have leaked this photo...[img] Found it when I finally got the gear set unfroze. A little oil soaking helps break 40 years of...
It is what it is...Saw an Ebay listing for a 37-48 truck axle and it looked very similiar 'cept for the round flange on the listing and my U joint...
My old mechanic said the look like old Power Wagon or truck diffs. He said the truck diffs look "funky". The weird one is a 4.11 ratio. Got some...
OK, got 6 and I know 3 so here are the other 3: only casting shown is on the twins. [IMG] [IMG] [IMG] [IMG]
Well, I know you got one right, maybe 2. Well see tonight. 62 Dodge 652 casting (superceded by more popular 741 casting)
Im picking up 700lbs of older 3rd members from a guy and cant ID half of them. figured you guys run the spectrum of badge fans so..some have no...
Talk about exhaust manifolds cracking! The head and exhaust slide a bit as it is when they heat up at different rates so introduce a fast heating...
What model Holley (?) is that wacky round 4bbl carb that is a spreadbore design, but the bores are REALLY far apart? Something like a TQ...
Thought about this and came up with a bench made tool. Take an old car exhaust valve, cut a slit in it about 1/4 inch deep. Go to your favorite...
Print-o-seal. Something to do with the surface prep that allows the head to slide a little on it when the AL expands faster than the iron block....
IIRC, There are actually 3 tailshaft lengths. The normal 18" or so in 2 versions, beefy truck with side circlip access and normal auto with bottom...
Yeah, cheap, but no air compressor. I got a Makita at work that goes down much lower than my "hobby press" And I can put some weight on it for...
Yup, it a 3 sided bit, and the LBJ is wedged against rotation on the press stand and is C-clamped to the base. I cant get the 5 speed spindle...
Separate names with a comma.