The Jalopy Journal
My .02 cents isn't even worth that. as a Hobbyist painter on my Junk, I have come to the conclusion that 99.9 % 0f painting is preparation and...
Lead Additives is the Biggest Gimmick ever to push Products, If you have and Engine with Non-Hardened Seats Which Run Bad Timing and Drive...
CJ Classic Trucks Fuel Sending Unit and Gasket for 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976...
Mine must be and odd Duck then. 1967
70/10 is El Correcto
Simply as I can put it, in South Carolina where it can be 10 Degree's in January or 101 in July, all of my Builds Operate at the same Temp Range...
So where is it above 160 degrees'
Heat Transfer is DIRECTLY and or Cooling is Directly Related to Time and Flow plus Surface Area. A thermostat is Dual purpose you are half right,...
So, a Thermostat was just something they pulled out of their Ass for Shits and Giggles.
Been in the Chemical Industry and Manufacturing of Chemicals for 30 Plus years, this is the Dumbest statement I have ever Heard, Heat Exchangers...
The opening event is True but recircling water at 180 is a Hell of a lot differ from than at 195, it's easier to pull 15 degree's out of water...
I would go to a 195 Stat, not holding water long enough
If you have the appropriate Axle Shaft Matched to the Bearing Set20 (3.15 x 1.562) or Sealed Bearing (3.150 x 1.531) will they Seat in either axle...
1958 4 cyl. Red Tiger wouldn't run for Shit with it, But all my Modern stuff with Compression, sits all Winter and Fires Rite up in the Spring
Take the rings off First......................If Trim Rings are behind Caps you could use Narrow Rings that would Clear the Caps.
If you set it to DC volts would it not show the Draw ?
I call them Super DumbAss's, That's when Two Dumbass's Breed they Produce a Super Dumbass. This is caused by all the Safety Equipment used Today....
Didn't early Bronco's have Offset Booster? [IMG] [IMG] [IMG] [IMG] [IMG]
Never heard of Warping Valves but I have Heard it will Speed the Flow up own the Exhaust Gases and that could be a Problem if Scavenging is...
Keeping original as Possible will always be Respected by me First and Foremost, but making Excuses for it or saying it's better than more modern...
It is Funny herein people compare 15000 volt ignitions to 40 - 60000 volt Ignitions. With Modern gas running Points is Ludicrous no matter how...
Motorized Fire Equipment, The fact that they Mentioned this lets you Know there was some Horsey's pullin Wagon's, and some Firemen smelling Hay...
1.5 OHM's for 6's and 8's, 3.0 OHM's for the 4's, will work like a Champ.
Is the Drums New, If they are, Probably need Turning to True Up........
I was Talking About the Housing of MC not the Fitting. I Have Put A Seat In Before by Filing down the Shoulder. The Fitting will not be Touched.
You can't File down the outer lip till Desired Depth is achieved for the Fitting?
Well from my Recollection there should be a Ballast Feed wire to the Coil in the Run Position from the Switch.
Is The Coil Still Firing to the Dizzy in the Run Position. I only run 8 to 9 Volts If you Don't Know History of Module Don't Trust It.
You verified power in own the Module But what about Power out? At Dizzy?
Any Chemical set long Enough it will Change State, or Phase. Shelf Life, Chemicals are made from Solids, set long enough and Degradation and...
Separate names with a comma.