The Jalopy Journal
How do I go to the slick 60s site?
I sent a post a few months ago about a 302 engine I put together for my 64 F100 was locked up. I thought about it and decided the eccentric I...
My 1964 F100 has an Aluminum grill and bright work down the side. It is very dull. What is the best way to make it shine?
I built a 302 for my 64 F100, having built many, but this 1 is locked up. I haven't torn it down yet, I think it is the cam locking it up because...
I built a 302 that was bored 40k. How many cubic inch is it now?
I have an older Ford engine with a flat tappet cam that I just built. I added Havolene oil and Rislone oil treament for older engines with a Zinc...
I looked at the question area of Hamb and it says"You have insufficent privileges to post here" How do I get privileges to post?
I submited a question yesterday and can't find it anywhere, so I will ask again. How can I get to my groups?
How do I get to my Groups?
I have a new Devilbiss starting line kit I used for the 1st time a couple weeks ago to paint inner fenders, hood hinges etc. The regulator didn't...
I put my 64 F100 cab on a 87 F150 Frame. When trying to put the power brake booster on the firewall it hits the cab and won't go back where it...
I plan to buy a aftermarket gauge set for my 64 F100 with an 87 F150 gas tank and sender. My question is what ohm range fuel gauge do I need and I...
My 64 F100 has a 8.8 rear end with 3.08 ratio. It has a 302 and Aod. What rear end ratio and tire size would be best for cruising and decent...
I saw in an Eastwood catalog, a tumbler that was priced way to high for me. I was on the Amazon site and they had tumblers cheaper. Eastwoods...
I hope this is the correct place to ask this question. I tried to remove the inside door and window crank handles today. even tried using my GM...
Is there any way to tell which balance crank I have? I have an 83 Grand Marq 302 with a crank that needs grinding. I also have a newer 302 with a...
Can a front cover from an engine with F.I. have the fuel pump hole opened up and used with a pump? 85 302.
I have tried for 3 days to sign-up for the fantsy bid on the Speed web site. They are also giving away a Shelby Mustang. They are having trouble...
I hope this is at the correct place. My 64 F100 Custom Cab has some clips that hold the trim that need replaced on the cowl. How do you get to the...
I am in the process of cuting out rust and welding in new metal on my 64F100. I either have bbs or blow holes in the old metal. I'm using an...
I hope this is the correct thread. When I cut out rust and try to weld in new metal on my 64 f100, I either have the heat too low (bbs) or blow...
I have seen billit gauge panels for my 64 F100, but has anybody seen any made from steel or somthing else and not already drilled?
I have a 64 F100 and I'm thinking of removing the drip rail above the windshield and keeping it above the doors. Good Idea or not?
I'm having trouble with Bondo. After replacing rusted out metal in my 64 F100, the bondo I'm using to smooth it out, dries after a couple minutes....
Been a member a short time and wish I would have known about this site before I started on my 64 F100. I would have done it different, after some...
I have a 1964100 and plan to put an 87 F150 frame under it. The 87 frame will have to be shortened, but it will have power st. and power disc...
Separate names with a comma.
The Jalopy Journal