The Jalopy Journal
Have a bunch of sbc's Got 4 BOP transmissions (3 350, 1 400) Thought using a BOP trans to sbc adaptor might open up some possibilities for me......
Gathering up some parts and info. to possibly put a couple sbc's together and have some questions: connecting rods- I know it probably doesn't...
Hoping to do some tuning on the sbc in my sons's '60 chevy p/u. Having an issue with leaky trans. cooler plumbing. I have disconnected the cooler...
Wiring a 10si alt. into the '52 chevy pickup. From what I understand a dashlight wired into the white wire from the alt. is required. I go to the...
Cleaning up some wiring on a couple of projects- My question is does anyone have any tips/tricks, advise on how to run and route the wire in a...
Redoing the fuel system on our '40 chevy p/u with a SBC. Its tricky to get the inlet/outlet situated without kinks and sharp bends in the lines. I...
Trying to wrap up the SBC install in my son's '60 Chevy p/u. No matter what I've tried I cannot seal up the thermostat housing to the intake....
2 front fenders, no spare tire well, rough shape but could be saved - $100 '26-'27 T box, pretty good shape - $400 If interested PM me and I can...
Have a pair of front '34 ford fenders that I believe came off a truck. Is there a way to positively i.d. what they came from? Is there any...
[IMG] What is the tool or trick to make a secure crimp with these type???? thanks
Putting an alternator in my son's '60 SBC powered chevy pickup. Basically rewiring as we go as the old wiring is missing or shot. Ran a wire from...
Anybody have any pics of 1960 chevy pickup lower rad. mount brackets for a SBC or know where I can find pics? Mine originally had a 6 cylinder and...
Rebuild a QJ for the sbc is my sons '60 chevy p/u. I installed new bushings on the primary and secondary throttle shafts (after reading that the...
Am looking to replace the gun in our bead blast cabinet (typical Skat style cabinet) and all the replacement guns appear to be about the same...
Want to move the fuel tank out of the cab of my son's '60 chevy pickup back between the frame rails under the back of the bed. I have a circle...
Years ago we were assembling an engine (forget what its was but 99% sure it was a 350 or 351). When we dropped the dist. in the guy I was working...
Anybody recognize what this came out of? I may keep and use it as a display in the classroom
Any thoughts on what this is from??? Thanks
Getting ready to attach brake/fuels to the frame on our 34 (2x3) rectangular tube. Was looking at the rivet nut tool to install threaded fasteners...
Where do the 2 brackets circled in red attach to? (not my picture, I copied it from here). We are channeling our cab and need to figure out how to...
I don't have access to the engine right now or I would just measure, am wanting to pick some up on the way to the shop. What length do the center...
Years ago I had most all his books, read and enjoyed them. Our school librarian asked if I had any recommendations for books that the "shop" kids...
Still piecing together the sbc for my son's '60 chevy p/u. While digging through my stuff I found heater hose fittings (ones that screw into the...
In class we are putting together a cut-away/display engine for demonstration, visual aid purposes. We are putting an autolite 4100 on it as I can...
Doing the SBC heads on my son's '60 chevy pickup and trying to measure the valve spring height. The valve spring micrometer from Proform tools...
My son is assembling a set of heads for the SBC in his '60 chevy. These are aftermarket heads machined for positive seals. I was stressed out as...
Can anyone tell me the length of '34 ford rad. support rods? I haven't been able to find the info and I would like to mock up my grille shell...
Am thinking about putting bear claws in our '34 p/u. The original ones are trashed beyond saving so I figure I may as well replace them to a safer...
So I think we will try to build a wooden seat frame for our '34 p/u. We don't have any of the original seat, the cab is channeled and we plan to...
Getting ready to get back to work and finish assembling the sbc 350 for my sons '60 chevy p/u. Stock bore, RV cam. Have a set of aftermarket iron...
Separate names with a comma.