Register now to get rid of these ads!

Screw dynamat. Peel and seel great sound dampening material....

Discussion in 'The Hokey Ass Message Board' started by Blake84, Jun 29, 2012.

  1. BuiltFerComfort
    Joined: Jan 24, 2007
    Posts: 1,620

    BuiltFerComfort
    Member

    Exactly. Also "Kool seal" mobile home roof sealant instead of latex paint is used. It's thicker so you roll it with a paint roller.
     
  2. hkestes
    Joined: May 19, 2007
    Posts: 553

    hkestes
    Member
    from Plano, TX

    X2 on the Kool Seal, but make sure you wear a respirator when you open and mix in the micro beads. They are very small and will blow around with the slightest movement, you do not want lungs full of ceramic beads.
     
  3. Good point they are really just like dust when you get them.
     
  4. Just went to the local Lowes in Moses Lake and picked up 4 rolls of peel and seal. It should be enough to do the floor of my truck.
     
  5. atch
    Joined: Sep 3, 2002
    Posts: 4,458

    atch
    Member

    i may be the only one on the planet that's had bad luck with the foil faced bubble stuff, but on the inside roof of clarence, the stuff seperated between the top foil layer and the bubble layer. the foil is still up there, but the bubbles fell down. i used one of the 3M spray adhesives (which worked great) to put it in.

    i may try the peel-n-seal and if it works perhaps paint clarence black again. the only (& i mean ONLY) reason that clarence is white is 'cause it's like a blast furnace in there in the summer when it's painted black. when it was black my friends called it the "easy bake oven".

    a pic of it in the black version & BenD on the salt:
     

    Attached Files:

    Last edited: Jul 22, 2012
  6. VoodooTwin
    Joined: Jul 13, 2011
    Posts: 3,455

    VoodooTwin
    Member
    from Noo Yawk

    A 2nd layer would add more mass between the noise source and your ears. So yes, there is an advantage. More mass = more sound deadening. Ditto for insulating against heat transfer.
     
  7. HotRodHook
    Joined: Jan 30, 2010
    Posts: 3

    HotRodHook
    Member

    Ok Guys, I hear its good for sound deadening, but what about the heat coming up from the floor and firewall ????
     
  8. 40FordGuy
    Joined: Mar 24, 2008
    Posts: 2,907

    40FordGuy
    Member

    "Fat Mat" ? Haven't heard of that one...Tell us more, please.

    Tnx,... 4TTRUK
     
  9. slammed
    Joined: Jun 10, 2004
    Posts: 8,161

    slammed
    Member

    [​IMG] Google the name 'Fat Mat' ALL the sizes and information of the product is there. It is a higher end (compared to the roof material) item.
     
  10. haroldd1963
    Joined: Oct 15, 2007
    Posts: 1,154

    haroldd1963
    Member
    from Peru, IL

    Thanks for posting!
     
    1950 Special Deluxe likes this.
  11. WZ JUNK
    Joined: Apr 20, 2001
    Posts: 1,663

    WZ JUNK
    Member
    from Neosho, MO

    I visited my local Lowes this morning. They do not stock the peel and seal. I have searched the Home Depot web site and I can not find it. I need to know the exact name of the product from Home Depot. Can anyone help me with the name or part number or post a link to the product on their site?

    John
     
  12. ohiohotrods
    Joined: Aug 14, 2006
    Posts: 412

    ohiohotrods
    Member

    good stuff-been usin it for years-now you know why scott whitaker can afford all the high dollar toys he has
     
  13. Blake84
    Joined: Feb 4, 2012
    Posts: 738

    Blake84
    Member

    Its not at home depo it's at lowes.
    http://m.lowes.com/mt/www.lowes.com...Ntt=Peel+and+seal&pl=1&currentURL=&facetInfo=

    Item #154017

    I hope this helps
     
  14. big creep
    Joined: Feb 5, 2008
    Posts: 2,945

    big creep
    Member

    Hi folks! So I tried making some today and this is what I got.

    Took this and added it to the paint. And this is what I got. I made a small amount to test it. I'm going to try that roof paint and just regular white paint tomorrow. I'll post the results for you guys then.

    the top of the test panel has the ceramic in it, the bottom half just paint. and then i took the temp off of the cement mixer. my test panel was only on the cement mixer for about 30 minutes. so its not much to go by, im going to try this again, but for now i just wanted to share what i got.
     

    Attached Files:

  15. sr808
    Joined: Aug 4, 2007
    Posts: 129

    sr808
    Member

    Thanks for sharing Blake! I'll have to try it.
     
  16. Mopar Jack
    Joined: Jan 24, 2010
    Posts: 1,363

    Mopar Jack
    Member

    I took a ride in my buddys 50 Chevy the other day,it has this in the doors and on the roof,works as good as Dynomat,but with 110 degree heat,there was a slight tar smell...
     
  17. 52HardTop
    Joined: Jun 21, 2007
    Posts: 905

    52HardTop
    Member

    [​IMG]

    There is also a product at the Home Depot that is just as good. It's under the Frost King name and is found in the HVAC section. It's used for insulating ductwork. I've used it in both of my cars. It works fine and has no odor. You'll find it in a plastic bag type of wrap. It also peels off and sticks to the surface. I used aluminum tape for the seams. Dom
    [​IMG]
     
  18. Doc Squat
    Joined: Apr 17, 2008
    Posts: 1,375

    Doc Squat
    Member
    from tulsa, ok

    I "painted" Lizard Skin in my deuce and then covered the whole interior with regular foil bubble insulation from Home Depot. No smell and sure made the noise level go down. Radio??? Who puts a radio in a hot rod?
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    Like I told the kid, "Your musics not too loud, its just like OKC, it sucks!"
     
  19. JeffB2
    Joined: Dec 18, 2006
    Posts: 8,339

    JeffB2
    Member
    from Phoenix,AZ

  20. Great info here, gents! Saved me a lot of moolah, and probably a lot of others as well.
     
  21. lakeroadster
    Joined: Nov 6, 2008
    Posts: 604

    lakeroadster
    Member
    from *

    Another use for peel and seal is as fender welting.

    I wanted to use some kind of fender welting on my truck but didn't want to use the stock fabric type due to its water retaining problems.

    Peel and Seal has a tar like black base with an adhesive on one side and dead soft aluminum on the other side. I cut it with sheet metal shears.
    [​IMG]

    I started by cutting (3) 1-3/8" wide x 19" long strips and sticking them to the fender lip. I used an X-Acto knife to cut the bolt hole openings. The aluminum is thin and soft and cuts easily.

    [​IMG]



    This shows the sticky tar side of the Peel & Seal.
    [​IMG]

    Once I installed the (3) strips I custom cut pieces for the corners. I also applied the Peel & Seal to the fender at the location of the step. This was one of the easiest projects I have done thus far on my truck.
     
    Last edited: Mar 19, 2013
  22. Roupe
    Joined: Feb 11, 2006
    Posts: 719

    Roupe
    Member

    Thanks for all the info. Got to try the Peal and Seal.
     
  23. '54Caddy
    Joined: Sep 11, 2009
    Posts: 929

    '54Caddy
    Member

    John, my old man and I went over to Home Depot because there is no lowes close to us. We found a product called "Quick Roof". It was a little hard to find but was in the roofing section. It has a yellow package. It looks identical to the Peel & Seal and was the same size, material, and price. We will be doing the floors in my fathers 58 Buick this week. I'll let you guys know how it turns out.

    http://www.homedepot.com/buy/buildi...-re-roofing-material-122397.html#.UBfQwMmF-Po
     
  24. mrconcdid
    Joined: Aug 31, 2010
    Posts: 1,157

    mrconcdid
    Member
    from Florida

    After reading this entire post, I desided to jump on board, I started last night at the top of the firewall and running thur the entire car including doors, floors, trunk and roof. I found the BIG roll at lowes for 86$ and Im using a hand roller to burnish it to the panels, also picked up a big roll of alluminum tape for all the joints and edges.
    Some Questions by others is weight this box says it ways 32 lbs and thats 100sq. feet of it. And there is no smell, I left a piece out side in the sun yesterday 97 degrees, and still no smell.

    Godspeed
    MrC.
     

    Attached Files:

  25. looks killer!
     
  26. Deadted88
    Joined: Jul 30, 2012
    Posts: 16

    Deadted88
    Member

    Is anybody putting this over POR 15? Wondering if it sticks as good.
     
  27. slammed
    Joined: Jun 10, 2004
    Posts: 8,161

    slammed
    Member

    Hey FNG, do the proper introduction. The surface is clean on the Por-15 hell ,yes this Peel-n-Seal stuff will stick!
     
  28. Buzznut
    Joined: May 9, 2008
    Posts: 2,349

    Buzznut
    Member

    Not to hijack this thread but...55 dude, can we see more pics of the ride in your avatar?
     
  29. tgd61
    Joined: Jan 24, 2010
    Posts: 51

    tgd61
    Member

    I just did my model A project in the Eastwood Thermo Barrier. Holy shit its a fn' mess!! The car is inside a garage that never gets over 90 deg. It's dripping melting, door pieces are sliding leaving behind skids etc. What's it gona do when parked in the 95 deg direct sun!!:mad:
     
  30. Blake84
    Joined: Feb 4, 2012
    Posts: 738

    Blake84
    Member

    That's awkward. I had mine in Palmdale 110 degrees baking in the sun all day and nothing. No smell vertical pieces on door were fine etc. don't know what is different about yours. Sorry to hear that
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2020 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.