Register now to get rid of these ads!

Looking for pictures of Model A rods with stock frames

Discussion in 'The Hokey Ass Message Board' started by 74bowtie, Jan 14, 2012.

  1. 74bowtie
    Joined: May 18, 2010
    Posts: 264

    74bowtie
    Member

    I am looking for picture of Model A Fords any body style, the frame must be stock but the suspention can be altered such as a drop axle in the front and the rear set up with coil overs or waht ever to lower it as much as possible with out altering the frame. I want to to pictes of your setup and then a picture of the full car to see the stance.
     
  2. Von Rigg Fink
    Joined: Jun 11, 2007
    Posts: 13,428

    Von Rigg Fink
    Member
    from Garage

    Im not sure if mine would qualify or not
    it is boxed, and x membered..but no kick ups, so as far as stock, the line of the frame has not been altered.
    4" drop front axle with a few leafs removed from the stock type front spring..and coil overs out back.


    this is the A
    [​IMG]

    and this is the build pictures..hope it helps..
    http://www.jalopyjournal.com/forum/album.php?albumid=290
     
  3. scrap metal 48
    Joined: Sep 6, 2009
    Posts: 5,891

    scrap metal 48
    Member

    4" dropped axle with flattened mono leaf front but does have 2" kick in back with transverse spring set up.......
     

    Attached Files:

  4. Slick Willy
    Joined: Aug 3, 2008
    Posts: 3,010

    Slick Willy
    Member

    Register now to get rid of these ads!

  5. 74bowtie
    Joined: May 18, 2010
    Posts: 264

    74bowtie
    Member

    I have searched quite a bit, maybe just me but I have not found what I am looking to see.
     
  6. bgbdlinc
    Joined: Jan 11, 2002
    Posts: 522

    bgbdlinc
    Member

    ...typical AV8 (Tardell) build.....

    [​IMG]
     
  7. Koz
    Joined: May 5, 2008
    Posts: 2,238

    Koz
    Member

    Some pics of my old roadster, now owned by Fryguy......

    [​IMG]

    [​IMG]

    [​IMG]

    This is actally a repro frame I fabbed although it is a dead nuts copy of an origional "Henry" right down to unused holes and rivet types and locations with one of my K members to support the '39 box.

    Hope they help. If not Fryguy on here may have additional pics.
     
  8. Stock frame, boxed, no kick ups. 4 bar rear with coild overs and panhard bar.




    [​IMG]
     
  9. 4" dropped Bell axle, reversed eye spring with 2 leaves removed, Deuce factory shorty shocks, VW bus steering.


    [​IMG]
     
  10. DK23
    Joined: Dec 6, 2004
    Posts: 123

    DK23
    Member

    '28, No kick ups.
     

    Attached Files:

  11. 1929CDAN
    Joined: Mar 18, 2006
    Posts: 344

    1929CDAN
    Member

    One of the BEST Model As on a stock frame!!

    orange 29.jpg

    orange1929.jpg
     
  12. 28- boxed, center k member, 4 in i beam front, vette rear
     

    Attached Files:

  13. 74bowtie
    Joined: May 18, 2010
    Posts: 264

    74bowtie
    Member

    Thank you everyone they all look great
     
  14. gashog
    Joined: Dec 9, 2005
    Posts: 978

    gashog
    Member

    My 29- Stock Model A banjo/reverse eye springs/750x16's on the back and a stock 32-36 axle with reverse eye springs/550x16's up front. Lots of good detail pix in my build thread (link below).
     

    Attached Files:

    Last edited: Mar 14, 2012

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2020 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.