The Jalopy Journal
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] 1951 Mercury coupe Complete body and frame No engine...
I bought this car 3 years ago and took it to Menges Twin Speed shop in Paso Robles for a full build. They chopped 4 inches up front, 8 in the...
Nice lense and backing plate...
Sold I’ve got a repro grill bar and used teeth for a 53 54 55 56 57 corvette. There a complete set of teeth plus a bunch of extras. All have some...
1954 Ford Customline 2door. Solid straight car, title in hand, no engine/trans, was a v8 car. Great start to a kustom project. Has nice patina....
1940 Mercury gauge cluster. Speedo moves when the input is spun. Not sure if the other gauges work or not. Glass and chrome show minor scuffs from...
Good shape. Stainless trim needs some typical scrapes/dents fixed and polished out. Tin itself is solid only bad spots I noticed were near the...
1950 Ford Club Coupe project for sale. $5,000 obo The body has been acid dipped, just needs finishing. Frame is clean and painted black. Comes...
motor has not been tested. Pretty nice shape. What you see is what you get. 250$ plus shipping.
***Revised listing*** see below 1949 Ford Tudor Sedan FOR SALE or TRADE Clean title in my name on non-op. Very clean, straight body. Already...
[IMG] So next weekend the Spokane Speed and Custom show is finally gonna happen. Grandpa and I will be hauling Taboo up to be in the show, any...
I have a pair of 1941 - 1948 Ford trunk springs. Springs feel tight and move nicely. Asking $100 or best offer for the pair. New ones cost a lot...
Sold
I recently traded an 87 Corvette straight up for a sweet 62 Buick Invicta done in a traditional custom style. Both side mirrors are shaved and I...
SOLD-Beautiful mild kustom '47 Coupe Deluxe, Long Door. 350 Crate, 700r4, dropped spindles up front, 4 link out back w/air bags, fresh pinstripe...
SOLD SOLD SOLD! I have found an old Offenhauser 0309 transmission adapter to mate a Buick nail head to a Ford transmission. I understand this...
1958 Lincoln Canted Quad Head Lights with Trim/Bezels. Hard to find. In very good condition. Very minor pitting. I bought them 25 years ago to use...
SOLD SOLD SOLD! I have the trunk lid or rear deck lid for a Ford Falcon, it's from a 1962 but might fit 1960-1963. YOU decide if it will work for...
[ATTACH] 1949 Ford Custom, chopped, shaved, frenched front lights, full custom tuck n roll interior, S10 clipped, disk front, 305 sbc, 700 R4, 10...
[ATTACH] [ATTACH] 1953 Chevrolet 210 “Mild-Kustom”. $11,500 OBO *CLEAN TITLE UNDER MY NAME* [ATTACH] - 235 Chevrolet engine - automatic trans...
This car was originally built back in 61 in Kansas. It was in speed and custom and hot rod magazine back in 63. I have tracked down the original...
I picked this bumper up and have no real use for it. Would love to see it end up on someones early custom. It's in good shape overall, will need...
Have the two corner pieces for the rear window of a 1956 Ford Victoria hardtop. Came off of a 4 door Victoria hardtop, but should fit two door...
**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD**SOLD** Vintage Bermuda Bell in beautiful shape. Sounds fantastic. Be the...
Ford spotlights for sale Not sure if they work, never tested them. In good condition, what u see is what you get. $150 shipped in the lower 48...
1948 Ford mild custom. Very nice ,detailed 48 tudor sedan. molded 47 Olds grille,frenched headlights,shortened chrome,Winfield molded...
[ATTACH] [ATTACH] [ATTACH] Selling my 1935 five window coupe. It has a Mustang II front end, Firestone airbag setup, Lincoln trans, no engine but...
New old stock grant Spalding flamethrower distributor for small block Chevrolet or big block Chevrolet. Bought this from big daddy Don Garlits...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] Parts from 1948 Dodge coupe Rear axle complete $50 Fluid Drive trans with...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
Separate names with a comma.