The Jalopy Journal
SOLD .....Like new, intake. See pictures for condition. I have other Chrysler and Dodge early hemi engines, let me know what you need
[ATTACH] Anyone familiar with these crane cam part numbers in pics crane j8174. R330hc D300
Purchased from an estate, appears to have been prepped to build and then sat, some light surface rust on the bores, bored to 35 to 40. The...
One is a little shorter. See pictures
Needs a good clean up. Will consider trades for Dodge and Chrysler early hemi parts and engines. I have other Early hemi parts available, let me...
Some rust around the oil fill, see pictures, I have other early Chrysler and Dodge hemi parts available
Extended bell with bottom bell housing. If you just want a part let me know. I have other 331 and 392 engines and parts if you need something...
I haven't been on the HAMB much lately. But 2 years ago I picked up a 40 Ford Standard Coupe. An elderly gentleman started a restoration in the...
Several 392 early hemi rods. $10 per rod/piston plus shipping.....I also havecsome used 392 lifters if anyone has interest
Casting 1677435, fits 331/354/392 early hemi engines
See pictures, I have other early hemi engines and parts for sale as well. Let me know what you need
Cam core I got with some 392 parts. It is marked with 569 so I assume it us the 1731569. I also have a set of 392 rods and a few other parts
Good shape, small ding and some putting in one of them, see last picture. Will consider trades for first generation dodge or Chrysler hemi engines...
Outside in good shape, inside had pitting, one has pin holes through. I have other Chrysler, Dodge and Desoto hemi engines and parts for...
4 bolt exhaust manifolds. I would consider trades for Chrysler or dodge early hemi parts or engines. I have other Chrysler and Dodge early hemi...
1956 354 dual quad intake, fits 331, 354, 392 hemis. I have other 331 hemi, 354 hemi, 392 hemi engines and parts for sale. I also have Dodge...
1957 392 standard bore engine. Unfortunately one cylinder has a crack and would need a sleeve (see the second picture). I would consider selling...
PRICE DROP $5,500 - Motivated to sell, to answer general questions asked- This engine is in a project car I bought to drop a newer drivetrain in...
Early Hemi log intake for 331 Hemi or 354 Hemi or 392 Hemi. It has a spot for a water port however it is not cut through and could be easily...
Hey, picked up a tunnel ram for a 392 Hemi yesterday produced by A.I.U. and found very little on their history or production runs. Was told there...
Early Hemi parts collection being sold as lot, sorry will not part out. Please call Metalworks Classics & Speed Shop with any questions. Parts are...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
Sold!!!!!!
I decided to go with fuel injection, so I am selling my Weiand #7263 2x4 aluminum intake. Comes with a matched set of Carter AFB carbs re-built by...
I'm working on the venting for my hemi. Its probably under 450 hp with dual quads. I have the PCV valve setup. My question is: How much...
I need to replace the rear main seal. Any advice on rope or neoprene? Also any tricks or tips? The motor is a complete running motor. I can...
I'm hoping to use a group 51 battery on my coupe. Its 500 CCA. I was using a 700 cca on a test stand. It always started effortlessly. I'm...
***SOLD***I’ve got what I’m pretty sure is a NOS flywheel that came off of a 392 Hemi I sold. It measures 14-3/4”, has a 172 tooth ring gear, and...
I have a chance to buy a 392 Hemi from a buddy. My problem is that I have no idea on what the high dollars parts are going to be. I did some...
Separate names with a comma.