The Jalopy Journal
Pair of vintage Fenderwell Headers that fit SBC engines in 1955,1956 and 1957 Chevrolet gasser passenger cars. Good condition. Too awkward to...
Long time member, I just never post. More of a lurker but I just didn’t want someone thinking this is a spam post. Anyways I have Weiand C536...
Long time lurker in the forums. Started rebuilding my own stock SBC 350 and was curious if this noise sounds like lifter tick or something more...
[ATTACH] [ATTACH] [ATTACH] I’ve been debating camming my small block for awhile now. She’s a bit old but a trooper nonetheless. I’m contemplating...
Very nice set of Mr. Gasket Corvette valve covers. They are slightly oxidized but would polish up very easy. No dings, scratches, or gouges. Look...
Vic Hubbard 350ci small block Chevy crate engine removed from a running/driving '57 Chevy. RV cam. Edelbrock intake and carb which was recently...
53 I picked up a while back as pretty much a shell no Motor and trans got a 350/th350 out of a 77 Vette and long tubes stuffed in and a ebay 4link...
So I have been dealing with trying to get a straight answer on sourcing the proper lifter for my 350. I think I may have found my answer, and this...
TCI Transmission mount for turbo 350 40 ford chassis $25 + shipping Eric 909 534 9531
I am upgrading to a 350 SBC in my 1954 Bel air.. What transmission would be best to go with. Turbo 350 or a 700r4.. and yes I am swapping out the...
Putting a 350 SBC in my 1954 bel air.. Can I use the stock radiator or do I need a different size or type?.
I have a 54 chevy and I am putting a 350 in it. I have seen many posts about using an S10 4x4 rear end with the drum brakes. Nobody has stated...
Hi, Just out of curiosity what if any would be the benefits of a 350 with 5.6 rods and the proper height pistons (taller)? Obviously you would...
So I have 1955 Chevy Truck with a 235 straight-six and have had it for about 2 years like that. I use this truck as a daily driver (30 to 45min...
SOLD
So first the story... I've been wrenching for years, but only recently have gotten to the point in life where I wrench for pleasure instead of...
Hi, So I’ve been reading and watching lots of videos on how to do a camshaft break in. Now I have to questions: 1. Is there a way to determine...
1962 Mark 2 Jaguar set up for 350 Chev. and 700R4 (included)-- engine/tranny are ready to drop in. Mounts done, wiring almost complete. Rear end...
Built a sbc 350. mild cam,High flow water pump,180° thermostat, dual electric fans w/ aluminum shroud they turn on at 160°. Just put the engine...
SBC 350. Using between 1/2 and 1 full quart in about 40 miles of driving, highway or in town. I'm pretty new to working on cars, and I'm trying...
This is a 350 that came out of a c20. It is a four bolt main. The engine is complete other than when i got it it was missing the oil pump and no...
Just joined the forum, though I've referenced many times in the past for great info. I did a search on the topic, but most of the posts are quite...
Nice daily driver 51/52 Chevy styline mild custom. Clear Texas title. All new glass and rubber. New soundproofing, carpet, upholstery (headliner...
i have a 1952 chevy 3100 truck ive been slowly working on over the years and im wanting to know, can i put a 350 in the truck?
For Sale: 1936 Chevrolet 2-door Sedan Humpback If you're not a pre-war fan, you're really missing out on some cool cars. This very sleek 1936...
Sold
sold
I have a 350 in running condition but ready for a overhaul. And a 400 that has sat for about 15years in the garage, and was "starting to smoke and...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] This is a 1977 Chevrolet Corvette engine it is complete minus a intake. It is standard bore, rods and...
I have for sale the Chevy 265 v8 engine that came in the bed of my 57 Chevy truck when I got it. It was sitting for years, so it is in pretty...
Separate names with a comma.