The Jalopy Journal
I am trying to determine the manufacturer of the following kit. This conversion came with the front frame stub that I grafted back onto my ‘40 and...
Hey guys, I am trying to raise the rear end of my 1959 Chevy Apache and was wondering if anyone has done that? I was looking for some air shocks...
So I decided to throw down on a Bowtie Overdrives TV Made EZ Kit for my 700R4/Edelbrock 1406. I came across this issue after discovering some...
Does anyone know when car horns became mandatory on vehicles? There had been a lot of legislation in each state between the 50s-70s.
My family and I just moved to Southern California and were wondering if anyone may have any shop space we could rent to work on our cars; 1940...
Some jackass walked into my garage and stole one of my drag tires/wheels. Unfortunately, they don't make these wheels anymore and the tire was...
I am selling my C10 to pay for my 1940 Plymouth Coupe so I can finish it. This is a good truck and would like to see it go to a good home that can...
Well, a new chapter is going to start for me here. I just accepted a job in the defense industry in So. Cal and will be moving in a month. I am...
Has anyone dealt with the guy from Obsolete FLM Parts (nosfordparts.com) in Jupiter, FL before? He deals with pre-1964 Ford, Lincoln, and Mercury...
The setup: C10 Pickup - Chevy 250: starter is 3 months old, most of the harnesses have been replaced and/or fixed..... older coil (doubt it...
Can someone photoshop a picture for me.. I am looking to have a 1959 Chevy Apache with a 1957 GMC Grill. I realize that it will need to be...
I need to find a 90 degree elbow (normally called a street elbow) with one male end and one female end (inverted flare) with both ends for 5/16...
Has anyone had problems with this company before? My Truck: 1966 Chevy C10; 250 inline 6 with 2 sp. powerglide. The original lines would...
So I have been noticing the pickup surging lately (figured it just had a vacuum leak due to the hillbilly rigged vacuum line that I had to install...
Well, first off, I have a ton of projects. This one kind of has been thrown in my lap, but I look forward to it! My parents are moving from...
My parents are moving down to Miami for my Dad's work and I was wondering if there are any local shows that happen during the week that are not...
I was wondering how hard it is to pull the speedo drive gear off the output shaft of the tranny. Any special tools needed?
Has anyone ever heard of this guy? He is a pinstriper based in Indy. Does anyone recommend him? What is a decent rate for getting something small...
This is kind of early, but my wife and I are planning to head out to the GG Columbus show on Sunday July 12, 13, 14. Who else is planning to...
So this is how my day went yesterday: I was planning on driving the '64 C10 over to a buddies house about 30 miles away to pick up some tools...
I am wondering if anyone else has had any problems ordering Rock Auto radiators? I received the following shipment damaged; if you shake the...
Okay, here's my problem... my Rochester 2b is leaking through the throttle shafts, it leaks gas in other places too. I need to replace it... in...
Okay, so I think I know the answer to this, but will ask anyway... This old starter took a dump on my '66 Chevy 250 in my '64 Chevy C10. I...
Hey I am looking for an adapter and what would be a suitable replacement for a Rochester model B off of a chevy 250? I am just looking for...
Well I got the carb cleaned out and put back together only to find that one of my tiny clips/keys broke off the metal linkage to the butterfly...
Hey Guys, I need your help in identifying this carb. I think it maybe a Rochester. [IMG] [IMG] [IMG] Thanks for the help! The PO over...
Hey guys, quick question for you out there with the knowledge or truck books with diagrams. I am looking to significantly reduce the 6 to 10 feet...
Well I finally made the deal after two weeks of waiting. A pretty close to stock 1964 Chevy C10 Fleetside is now in my driveway. It has two...
Hey guys, I just got back from the Kyana swap meet in Louisville and went to talk to the POR-15 guys. I asked them about the truck floor on my...
Does anyone know if a 41 dodge 4 door frame will fit under a 1940 Plymouth coupe?
Separate names with a comma.