The Jalopy Journal
Here is a old thread for tube chassis hot rod. http://www.jalopyjournal.com/forum/showthread.php?t=714725&highlight=round+tube+hot+rod+chassis
PM sent.
Nice Project. Welcome from Salisbury, NC.
Welcome Daniel, From Salisbury, North Carolina.
They look like the ones from 65-68 Merc trucks (Hood Letters). Sorry no pictures.
Welcome from Salisbury and have fun on The H.A.M.B.
Welcome from Salisbury, NC.
Try www.vxb.com for loose ball bearings. Had to buy 1/4" to 1 1/8" bearing balls has they were called for passing mandrel bent tubing for NASA.
Congrats gene on your induction! Just received this in a e-mail for the Induction and Car Show.
It depends on your aftermarket gauge end, but a regular Ford 3 speed or c-4 speedo cable will work or you can use a lokar kit SP-1502U (Black) or...
73-76 Pontiac 400 cam #9779066.
Give Doug at Horse Power Engineering a call at (626) 440-0440. He can do tight radius center bend on stainless. He did some 5/8" stainless u bends...
You might want to check the end play of the distributor shaft, it may have to much play. I had this problem on my 64 F100 y block points...
Give D & D a call they make a kit for Ford vans (541)740-9468.
Orange wire goes to Battery (12 volt Positive side). I have installation instructions somewhere.
Thats why I only buy Miller Equipment, they have the best Customer Service for welding equipment. I have a Dynasty 200 and a 350 welder.
For a Machined looked the lathe is the only way. If you are sanding it I would use 120 or 150 grit with WD-40 or PB Blaster. It will leave a nice...
Here's a 49 I am doing alot of work on. Just finished building the motor, trans and rear end. Next is rewiring the car and vintage air unit....
Quain, again you do great work and fast. Just wondering are you going to be running ADRL or X-DRL this year with the Pro-Mod?...
^^^^^^^ X2 on these 2. You might want to take it to Joe & Jill at Superior Automotives. He always loved them Hemi's.
I am extremely happy with the Logo Design Chris did for my Shop. He is the only I Designer I will be using from now on for Logo & Rendering...
Lokar makes a u cut to fit kit. SP-1500-U108 fits GM trans to 3/4-20 speedo. This is what the Tech guy at lokar said to use. Same kit I used for...
QUAIN FOR PRESIDENT!!! Just wanted to say it. The work on the Car is BEAUTIFUL, your doing better work than most of the Restoration shop in NC. If...
Super late for this thread, But I am in Salisbury, NC.
Rewired a 63 Cadillac using American Autowire Highway 22 kit. Mainly use American Autowire and Rebel Wire Kits. Doing a all black EZwiring kit on...
Donkey's that a great one. I think he is trying to figure out all these different possibilities. Guess you could just build a new Garage where the...
31Vicky those parts you painted looks great. You are doing a great job keep us updated with your progress.
I think Jeff J is thinking of Its Finished. The number & address is listed below. Its Finished 4330 Indian Trail Fairview Rd Indian Trail, NC...
You might try Team C in Bellflower. They are off the 91 between the 710 & 605 freeways. If I remember correct the #562-866-3887. They have there...
The only shop I would take my crankshaft to when I lived in CA is Castillo's Crankshaft in La Mirada. Most engine machine shops send it to them.
Separate names with a comma.
The Jalopy Journal
