The Jalopy Journal
Ever since Ryans thread and build of the full-fendered side project in 2016 that little A couple has consumed me. I started my build about four...
Threads look good, little to no pitting in the water passages. Needs cleaned and ready to run. $100 plus shipping or local pickup always welcomed.
Bought for a project but wouldn’t work for my set up. What you see is what you get. $40 plus shipping.
5/8 36 spline to 3/4 DD with two 8” pieces of DD shaft, also 3/4 Hiem with jam nuts included. New, new never ran, bought for mock up but went...
So I built this car from the ground up. The Vega box is placed where the pitman arm puts the drag link and tie rod parallel. That interfered...
1962 Chevy C10 long bed. Strong 454 with high lift cam, Sanderson headers, aluminum radiator. Power brakes, steering. Rebuilt front sus,...
Three 1932 Ford V8 speedos, all 90MPH. One rare hard to find Waltham ‘32 speedo, works good on power drill, numbers on the mileage drums...
My current build is a pretty basic model A, ‘28 coupe, SBC, TH350, full fenders, ‘28 shell. Going to try AC for the first for me time in a old...
'46-'48 ford banjo rear, spins and feels good. Never had the carrier open, bearing surfaces and axle surface/threads very usable. No brakes,...
What you see is what you get. Decent model a frame, no rust, clean and clear numbers. No title, bill of sale. Old "hot rod" frame so has some...
Sold
Nice early bell housing with the early starter mount cast on and good flywheel. Prefer pickup. $60
Sold please delete
sold
Crossmember sold. Pending payment for spring.
Lights, bracket, air maze, ford script hoses, 6 volt pusher pumps $20 each. ‘32 PP. pitted, threads ,messed up, weld onto repop PP’s? $40....
Early no side mount 283 pulled from running ‘57 four door. Stagger bolt power pack heads and stagger corvette valve covers. Heads have been...
Oldsmobile rocket 350, pulled from great running 70k mile ‘72 Delta 88 about 10 years ago and in this same spot indoors in my garage since. I...
Very close to stock and original ‘32 ford roadster. Chassis is from a older restoration with rebuilt diamond B moter, rebuilt B trans, original...
‘13-‘20 model T repop fuel tank. The most popular one for all kinds on traditional rods and speedsters. Bought it about three years ago and...
Off old hot rod back when chrome was cheap and everything that unbolted was chromed. Not show quality but not flaking or rusty at all, some...
Bead blasted, gasket surface trued, glyptaled inside and painted black chassis enamel outside. ‘32 rear mount with spacer ring and special...
Selling off spares. All bead blasted, gasket surfaces trued, glyptaled inside and painted black chassis enamel outside. 78-7085 ‘37-‘40...
Fresh off my roadster just going a different route. Set of SBC lake style headers with the cork screw style baffles inside and turnouts. Just...
clean nice round back spindles. King pins and bushings are usable or wouldn’t hurt to replace, came off my running driving roadster just found a...
I recently bought a old hot rod body that has a ‘40 ish windshield grafted on. The windshield is the main reason I bought it and fell in love...
Complete T cab and A bed. Came off my running driving chassis that I’ve driven everywhere but going to coupe body so it’s for sale....
Newer Riley down draft intake with 2 recently rebuilt Stromberg 97’s. Was supposedly on a running car but switched to single. I got in trade...
I have a pretty much new banger downdraft and eldebrock 94 carb with linkage and air cleaner. Everything to bolt right up to your banger. Set...
On my ‘32 I have a stock repro tank from Vintique. Before paint I had it on the road for a little after mock up and the small brazing on the...
Separate names with a comma.