The Jalopy Journal
Was it single spring with damper or double spring? Single would indicate flat tappet yes use oil with 1000-1200 ppm zinc and phos.Double spring...
Have a home depot pump pesticides sprayer with super clean in shop wouldn't be without it. Purple Power sucks!
Looked into having a set of Buick wires restored and found out it was a lot cheaper to by good ropops if there is such a thing.Probably cheaper to...
Have to agree with Crazy Steve on this one you know exactly what you have there and a rebuild with a good cam intake and some minor head massaging...
When I was just a youngster many moons ago I always hung out at my fathers body shop and loved to watch him work lead.That and the air hammer were...
Grand General make every conceivable light in LED I know not very traditional but in case anybody is interested that would be the place to...
Not familiar with that number.Is it 9000 series or forged.the forged ones usually use chamfered bearing .The cast uses regular bearing.
I will take my motel room with me(Freightliner Condo),get paid to drive it down,stay at the Flying J for free get free showers may even plug into...
Won a case in court similar to this years ago and really didn't expect to get anything out of it but,a couple years later he decided to refinance...
Plenty of aftermarket valve covers but for the oil pan you have to venture over to the marine world.Problem getting one cheap.
Sorry Ridge Equipment in cheyenne.Dont know where that other name came from DUH
Try Ritchie Enterprises in Cheyenne (behind Flying J) they put a clutch in my Freightliner last month didnt look too busy.
What??!! no CNC program for these cars yet.
X2 on seeing more of this boat.Would not mind having that trailer too.Post more on that boat on the "Vintage boats whose got em" thread
OMC had a marine version 225 If I remember correctly had one in a 19 ft Slickcraft(heavy boat)moved it along quite well.Tons of torque for a small...
Had two of them in mid 60's Resorters and they ran quite well with 4bbl's.Side drafts had a lot of torque but lacked on top end.
Lindblads in Northbridge did a bunch of work on my brothers car years ago,still there?
Funds were very low so I went just for something to do. Was amazed at lack of junk and some good deals.Think I got it figured out go broke and get...
Get the timing cover off. Chain or Gears?If it has gears you can't just spin it other direction because pistons are flipped for right hand...
Walked into Autozone years ago put an altrnator on the counter went through all the what year?what engine? what trans? what color?What phase of...
I go thru there once in a while it's a nice ride from Las Cruces to Amarillo lots of nothing and no traffic.I will probably be in Phoenix next...
Screwdriver if it needs adjusting,pliers if it needs rebuilding,hammer if it's hopeless. Been doin' so much with so little for so long now can do...
I don't know about the cheaper China crap but the prices are a little better on the name brand stuff.I called on some piston specs and the person...
You will need probably a -21cc dome to get compression up to 10-1 assuming you are not going to deck the block.The 300cc ovals on those heads will...
I just saw something very interesting on a "how they make it" show which might help to do this,crazy bends on musical instrument French horn I...
Sent PM w/#
I will coming up I-81 on sunday can p/u in Lebanon if you can get them to Loves travel stop. Going to Southington Ct
HandymanMan, Have you been on the CorrectCraftFan site they will know everything you need to complete that project just don't say anything "non...
I used it on a cracked float bowl on an old shovelhead carb it never leaked a drop.Did it as a temp fix ended up selling bike saw buyer 2 years...
X2 on med rise fact manifold.I ran 2 600s holleys with no progressive linkage,fatten up primaries on rear carb 1 or 2 sizes never missed a beat
Separate names with a comma.