The Jalopy Journal
Pertronix recommends using a 0.6 ohm coil with their igniter 3. I bought one of their .6 ohm coils and checked it. it checked out at 2.0 ohms.
Bringing this older thread back up due to recent article I read. After doing a google search, I am no closer to the answer of which coolant to...
I've owned cars with the BW overdrive units off and on. I have always read that you have to take the od out before backing up. What damage can be...
Being as there are some Hudson guys on the forum, I thought I would post this from Dan White- [ATTACH] OK everyone I finally have the final...
Here are pictures of the areas I need to repair.
Has anyone here used the Crown Alloy 44-30 for welding cast iron exhaust manifolds? I have a hudson Twin H intake manifold that has a common rust...
This does bring up another question. Should the dash temp gauge wire run from the sending unit in the side of the head or from the one near...
I have one of the tube insert into radiator sending units as well, but somehow hate them! Anyway, thanks for the info guys! The spal tech advised...
I'm converting over to a dual fan aluminum radiator set up on a 350 sbc. It has two different temperature senders , one in the intake manifold...
Yes
Yes, that is the method! He just told me that after the block is shot peened, all of the shot can not be removed and winds up in the oiling system.
I just had a friend tell me about rebuilding his 1954 motor (Hudson). When describing cleaning out the rust and scale in the block and discussing...
"I am wondering why you could not make a tv cable bracket that would fit/be part of the gas pedal linkage instead of at the carburetor. As long...
anyone used this system? https://www.bowlertransmissions.com/forums/automatic-transmission-tech/700-r4-200-4r-tv-cable-kit/
The old hydromatics (50's) don't have a TV cable, only the hard linkage.
The carbs on this flathead six set off to the passenger side of the motor. Not in the middle of the valley like a V type motor. The linkage also...
I am wondering why you could not make a tv cable bracket that would fit/be part of the gas pedal linkage instead of at the carburetor. As long as...
I have the June 2019 Hot Rod mag in hand and there is a good article on the TV cable variants and how to adjust them. It looks like all address...
Mike, what rearend are you running on the one with Wilwood brakes?
I just want to think everyone for all the advice and tips for this project! I have a June 2019 Hot Rod mag coming and have looked at and...
I have a 2004R that came out of an 86 Monte Carlo that I am getting up the nerve to rebuild myself just for the experience. I want to install it...
I remember reading one of my Studebaker books about the original roof line that Bob Bourke designed had height added so that a man wearing a hat...
Brian, I would be interested in the trans conversion kit if he still has it!
Thanks!! (HubCap Mike says these won't work on the Hudson wheels. Look closely at the Hudson wheel picture and the inside of the cupped area is at...
Im looking for a set of baby moons that fit on a 15" wheel with the spring clips, not the bumps. anyone know what will fit? Most I see are fit...
I can't get a reply from Hunter service on this. It is an older machine so guess they don't want to mess with it. Maybe one of you Hunter guys...
Yes, it has a return spring that acts as an over-center spring.
Ok, I have searched all over the web about this subject without getting a definitive answer. For a street car is there a definitive answer of how...
Update on this project- (6cyl, 6volt positive ground 52 Hudson) Prier owner had put a Clifford 4br intake manifold on and a set of long tube...
More info- The system has been changed to a pertronix igniter and coil to match. Pertronix says not to use solid core wires. I may have to switch...
Separate names with a comma.