The Jalopy Journal
I have a question about the size of the carrier bearings on a Detroit Locker. I see some of them have a 3.250 bearing and are specific to a 3.250...
I noticed on other Model A's when the fuel tank and windshield are out there is a cross-member at the base or bottom of the windshield where the...
Well im in the market for a scoop on a twin holley setup over a 671 supercharger , Cant make up my mind on what to go with, ether: An alum finned...
I'm in the market for a steering wheel as well as a column, I'm thinking on going with a 13" over a 15" for more room. anybody with a Model A...
I'm in the market for a steering column for the 31 A coupe, I have no Idea how long I should be looking for, I see a lot of after market one's at...
Well after gnawing over the thought of polishing my 671, making a buffing wheel, polishing a few small parts, I decided to paint my blower,...
I have a 671 blower that I'm rebuilding/converting. I'm at the point of reassembling it. I see a lot of high dollar blowers on here that appear to...
Curious to know what distributor you guys are using on your on your SBC with a 671 Blower? are you using a boost retard? Vacuum advance?, Im sure...
Im building 6/71 supercharged stock sbc 350, it'll have two 600 holley 1850s w referenced power valves, my question is can I use a mechanical...
I picked up a 671 GMC blower and need to know the best pulley tooth count, It will sit on top of a stock 350 chev 1970 truck 4 bolt block and 441...
Free Shipping at Speedway thru 12/1. Just thought Id throw that out there for any body that Uses Speedway for parts. Iv'e spent a lot of coin...
I've only painted 1 car in my life and it didn't turn out too good. I want to paint my car with Lacquer being you can sand out runs and...
I posted earlier if anyone had made their own grille insert but there wasn't much info on it. I seen an add on ebay where a guy was selling a...
Im mounting a 32 Radiator on an A frame, Im curious if you guys use radiator mounts such as these that I found at So-Cal. or do you just bolt the...
Dont use photo bucket, it seems to delete your photos after a certain amount of time. Iv'e seen many older posts here and people post there photos...
I have a 31 A, It has no floor in it at all, I have an A frame with the stock rear cross member it, I'm going to remove the rear cross member and...
Hey guys from MN just wondering how hard it is to get a title for your car, what info did the DMV ask for, I have no numbers on my 31 Model A...
Wondering if I should paint the inside of the body with POR-15 first and then continue on with the body work patch panels sub-floor etc. Or get...
Just got this frame and wondering what the brackets pictured are for, I think the larger one toward the front is for the hood, is the one toward...
Bought a Model A frame and it came with this cross member, does It have enough drop? I have a 3-1/2 drop I beam axle and stuffed up inside the...
I got this with the 31 Model A but I want to run a 32 grill shell. this radiator is about 29 inches tall and 17 wide. I think its from a 37,38,39...
Anybody seen or make velocity stacks that have individual tubes for each barrel that can be installed on a 4 barrel carb? I think it'ed look cool...
Would it make any sense to buy new side sub rails (the one that go along the length of the sides) If I'm going to in stall a steel sub floor? do...
I looked every where and cant find rear wheel arch patches, no one seems to have em. Any body know a place? I know a lot of you are skilled in tin...
I picked up a chrome 31 1/4 inch front spring on the cheap, the chrome was pealing and some rust, so I sand blasted it. and now it looks good....
Ok im new and stupid, now that thats out of the way, what does FNG mean :confused:
I picked up a 9 inch ford housing, 3 inch tubes all the way, big bearing, full round back, with drain plug at the bottom, 57 inches outside tube...
I've seen some Ansen sprints that have been redrilled for duel bolt pattern but the back side where the new bolt pattern looks like it wont...
Anybody make their own front cross-member for an A or 32? I did a search but couldnt find any. Thinking maybe using channel and pie cutting it for...
Separate names with a comma.