The Jalopy Journal
Just saw this, maybe someone posted before: ‘Elliot Ness' (Actor Robert Stack) used to race a Model A roadster out on the dry lakes of California....
Maybe if it was channeled and was running a hemi, you might want to chop it, but as a banger it is perfect. Warren
We are in the process of building another banger using a S10 T5 this time, used a jeep the last time. I just talked to Dave at Performance...
I installed a set of plug wires from Wired Customs on my banger last summer. I was very impressed with them and about 5 weeks ago ordered and...
Bob Beazer, was a friend. Met him at the 62 Nats, we were both Canadian. We often ran into each other and then I moved to my present home 12...
Why would you put in that ugly firewall when pulling back the bottom is easier, cheaper and looks better?
I posted on your other thread about the firewall mods. You can see in the pictures the motor mount. Here are a few more maybe to give better...
Have been running ATF in my T5s (5, both Ford and GM) for 30 years, both WC and NWC. Never had a problem and the synchros work perfectly. To the...
Place this jewel in your engine compartment. Fenton intake complete with heater plate and fittings, Rebuilt Carter-Weber 32/32 carbs from...
Has anyone used Raleigh bicycle forks or any bike fork to mount their fenders? I have heard good things about the look, but have never seen them...
If you are running a 10" with the counter weights, The 10.5 uses the same mounting bolt holes to the flywheel and has no counter weights for...
I currently have a 9" V8 clutch in my banger, no problem. I want to install a 10" clutch in another banger on a Burtz flywheel inside a AA bell...
By the looks of it, you created the 1" pocket by using the adaptors. The M12 x 1" are an unusual plug, but get the job done. I would imagine the...
I have a set of McGurk rollers installed in my 235/261. The are also held in alignment in a similar manner. I am just removing them and they are...
It's March 4th and we're not marching on? Warren
Jeff Norwell introduced me to you in 2014. He and I had our cars entered upstairs that year. After the introduction, I started reading your...
If that is a Speedway Vega box, open it up and check the bearings. They had a bad run. I was talking to a buddy last night who has one and in...
Yesterday I went on a little road trip. 500 miles in 12 hours. Two members on here needed something and I knew where those parts were. ‘tywy’...
I just removed the original springs and replaced them with Posies reversed eyes springs on my RPU. No where did I see the dummy plate on the...
Actually, I think we have found the answer. I have looked at that self cancelling module suggested by 29 Gizmo many times but did not want to put...
If this hasn't happened to you, you haven't been driving your car. You're driving down the hiway and go to make a left turn. You flip the signal...
That is really nice and clean and a perfect solution around the headers. Warren
I used that picture that Airborne 34 posted and made one vey similar except with pivot balls. I'm just waiting for my 2nd 97 to show up. I...
I guess it all depends on how pretty you want it or what you value the intake at. I would put a compression fitting in the header with a 3/8...
Did those rims work with the AR drums? Warren
I ended up making one from the pattern from Scalded Dog Speed, a C.Yapp company. I used aluminum vs steel and have no problems. Hope this...
[IMG] That down loop in your fuel line and gravity with a down draft carb don't work. You need one of these. Warren
I have just installed my equalizer intake with a pair of 97s. The intake does not come with a throttle arm and the one off my Ansen is not very...
The real advantage to the Buick/Olds 215 is the weight. That 305 lbs makes the A front end handle like a dream. I love the engine and have built...
Separate names with a comma.