The Jalopy Journal
I used pre-polished 304 S.S. 1/2" tubing to build this one my '69 El Camino. It remained shiny for the 10 years I had the car. Use tubing bender...
It was 1978 when I installed a 1965 Corvair frontend under my 1938 Chevy Sedan...Drove everywhere and had no problems...With that said, this was a...
Your Chysler is looking good....When finished it will be a cruizer for sure...Here is my '61 Windsor Chrysler I've had since 1995. Keep up the...
Make sure your Unilite is grounded to the engine block per a Mallory Tech when I had a similiar problem.
Correction....I just checked my spec's and the R&P was out of a Pinto...
In 1978, I used a 1965 Corvair w/ Mustang R&P. I mounted the R&P so the tierod ends would match as close as possible, the same scribed arc as the...
Hey Mick...Frankee has nothing on Forrest!!!:p
Sedgwick Streerodder's have been holding this Swap Meet the last number of years at the Kansas State Fairgrounds in Hutchinson, Kansas. Sometimes...
I'm loaded up and stopping by Mulvane to pickup acouple of hoodlums Friday. Will be there Saturday. Should be good weather.
Received the C4 and the rebuild is very good quality...I'm satisfied...Communications was RLH's biggest mistake...I believe after communicating...
Will do, I haven't got it yet..:o
My '57 F100 has a 292 y block and all mounts match the original 272 points. The bottom radiator outlet is on driver's side and top inlet is...
UPDATE......The contact I made to the company he works for paid off...The transmission is being shipped....I guess that action was the pressure it...
I'll call his company Tuesday if I don't get a reply from my email.... I went out of town for a C4 because I wasn't having any luck finding a...
I'm not complaining I just want to alert people about this guy. I've notified the company he works for, since he used their email address as a...
I was taken for a ride when I purchased a rebuilt C4 Transmission. It has been 3 months since I ordered the rebuilt C4 and now there is zero word...
How did my last year's post come up today?????:eek:
I agree with all the above, but if I may, a short story about J-bolts. It was 1959 when I ask my Dad if it would be Ok to lower my '57 Ford. His...
Leaving Broken Arrow Friday morning..Will be arriving at Jack's around 10:30 with plenty of fuel for his gas pump to start his pit....:o
For the clutch slave cylinder, try the Wagner P/n F124369...
The 60-62 Chevy Truck dual master cylinder P/N F87167 will work.... This will make you a nice setup.....
You'll need to use '59 or earlier Buick Backing Plates with an aluminum 1/2" thick spacer. You can use later finned Buick drums with this. You can...
This wiring is the same as '57-60 Ford F100. The light switch is probably your problem since your tail lights and stop circuit and headlights go...
I used 1/2" 304 stainless steel tubing to make my tube grille for the '69 El Camino. There are 4 vertical s.s. flat bars cupped out for the 1/2"...
Quad 50's and duster faw training in white sands new mexico.... What am i doing here mr. Custer!!!!!
Class of '63 Sedgwick, Ks.
Here are afew pic's....Hope you can see what was done using the 2x4 sq. tubing. The tubing is laid on each side of cab and resting on the original...
Use 2x4 square tubing laid on either side of cab interior on top of existing cross bracing and weld. Cut the original cross braces out and move...
Make sure your front yoke is greased good with telfon grease. Also check your yoke for wear.
Just two years ago, all Hotrods & Kustoms, even Street Rods, were welcome to park in pits and run if they wanted to. Now after last year's zoo,...
Separate names with a comma.