The Jalopy Journal
[ATTACH] 53 Caddy headlight bezels - $20 Early Chevy/Mopar lowering blocks - $50 Old bumper jack - $10 216/235 Chevy rotors and caps - $10 54...
Anyone have a diagram or method to install 1949-54 chevy spindles on fatman dropped uprights for a 1953 chevrolet passenger car? It seems like the...
Anyone know where to find 53-54 chevrolet passenger car steering box parts? My box has some slop, but don't want to get into it unless I know...
Does anyone know how a torque tube separates from a 3 speed transmission in a 1949-54 chevy application? Does the back of the transmission have to...
What would be the recommended amount to cut when C'notching a frame with a piece of steel pipe? Should half the frame be left intact? or can it be...
Anyone have a site that list GM 10 Bolt Rear Axle casting numbers? I have a rear axle stamped 22522676 X on the center.
Im building a SBC from the ground up. Its got almost everything new inside, but I've realized I have a problem. I'm using an old Edelbrock intake...
for a 53 chevy passenger car? Mine just started to leak!
I just finished my taillight idea on my 53 Chevy, kinda 60's Alexander bros. inspired [IMG] <br> [IMG] <br> [IMG]
I have converted my car from 6 volts to 12 volts. I did all the precautions for changes to the lights and guages, but my blower fan for my heat is...
This is an easy tech, most people could probably say just silicone or glue the bullet to the wheel but I wanted to make it easily removable. BTW...
A few pics from the show
Its not done yet but a friend wanted ghost flames on his jet ski, I convinced him to make them stand out a bit. I just basic BC, CC black and I...
I just finsihed my first entire flame job on my friend 51 Plymouth with a good amount of help from my cuzins Merc-o-Madness and TheSupersized and...
Ive been trying to install my rear wrap around window in my 53 chevy. Ive installed windows in a smaller car with less curves but none as big and...
Got my 53 chevy about 8 months ago, come to find out the clutch was shot so i had to pull the motor since it easier than pulling the whole rear...
Just out of curiosity what are some pros and cons of a 318 poly block engine. How come i dont see many used in hotrods and customs? is it cuz lack...
I am trying to start my 235 inline 6. I have converted it from 6 volts to 12 and am using a ballast resistor between the ingnition wire and coil....
My master cylinder has both the brake and clutch pedals piviting through it. In my repair manual it says to remove the foward plug of the master...
My school NJIT hosted a Trebuchet building contest this past weekend. It was called junkpile wars. 11 teams had to build a trebuchet from a pile...
409 with 6 carbs not bad. Foose said it was a "hotrod" motor when he saw it...
I ran out of gas on the parkway today and pulled over into the shoulder. I called my cuzin to get me some gas in a container because he was near...
i know im flogging a dead horse but does anyone recommend got flames flamethrower kit over autoloc or vise versa. i just want a natural flame and...
This is a 1980 Eagle 3 Moped, im pretty sure its 49 cc and pretty ugly stock. Me, mercomadness, fatty mcguire and the supersized chopped it down....
whose the best rod builder? Is it...? [img] [img] 30 a sedan, chopped 4, channeled, buick 394 nailhead, samson headers, 6 strombergs,...
Hi my name is matt, im from bloomfield, i love old school rods mostly a's, i have a vintage vw but i know u guys dont like em on here so im not...
Separate names with a comma.