The Jalopy Journal
Got a call this morning from Dave @ Drop'n'Stop. He says from my description that these are the Fatman spindles. Good to know. In the past I've...
Thanks OD ... I didn't know that the stock '55 used a bolt-on steering arm. When did Ford switch? My '58 had a one piece spindle before the...
A few years back I purchased a '55 Monterey from AZ. It has sat for over a year while I had other priorities. I decided to get it running again...
IT1 (SW/AW) USS Abraham Lincoln (CVN-72) 1997-2001 NCTS San Diego 2001-2004 USS Peleliu (LHA-5) 2004-2008 CID LS San Diego 2008-Present
#41 ... I still read daily.
Good Advice there ... Only ever had one explode on me. Using it in a Makita 4" grinder ... no guard of course. Luckily it shot straight down and...
I've seen zero compression and a burnt valve more than a few times ... Only way to know for sure is to check ... I usually use Fast Fords method.
Anybody know of a place in So-cal?
I did the same as Highlander .... Picked up a 1998 3phase Champion 10HP compressor ... Cheap. Rated Something like 37CFM at 100psi. Has an oil...
Man ... what a mess. I've been active duty Navy for 10 years come January. Been on a few boats and have done a few deployments. I'm sure I can...
Joined the Navy and was stationed up in Everett for a few years. Hated the weather and wanted to be closer to family. So came back home. Took...
I had a little trouble with just one on my HF 12-ton ... Although it might have been because I didn't have a better set of arbor plates for the...
A fella on the FE forum just did an intake ... Turned out pretty good. http://www.network54.com/Forum/74182/thread/1157868791/
I'm just a hobbiest myself but you'll have to pry my Snap-On flank drive plus wrenches from my dead cold fingers. Best wrench money can buy....
Chuck, I could use that stuff if it's going to end up in the classifieds ... Not sure that I still got your number. You still live off...
word ...
Right on man! Congrats ... R/ IT1
Blown fuse ...
I'm heading north tomorrow and coming back on Sunday. Think you can get them to Anaheim? Gimme a call 619.334.8628. Anthony
Well I'm in San Diego ... I just got it. Gonna watch it in a few minutes. Thanks Evel.
Edelbrock made the F380. A 3x2 that used Stromberg/Holley carbs ... 3-bolt base. Show up on Ebay pretty often and go cheap. Here's one on there...
Thanks DaBond ... I'm seriously looking at that option. Here's a little something that may have already been posted....
Burned-Up you can come down here and pick up my Millermatic 135 for $400 ... about a year old and in great shape. I just want a Millermatic 175....
I got it Wes ... tried calling you a couple times. Thought I had left a message. PM me or give me a call tomorrow. Thanks for the response...
Compressor died and has been holding up work for a while. I decided I'd buy one of them 7.5HP 80gal units. Then I was cruising Ebay and found this...
Summit part no. '66-'76 Ford C6 TCI-448800 ...... $189.88 '77- up Ford C6 TCI-448900 ...... $189.88 '66-'76 Ford C6 (Heavy Duty)...
I think Summit sells one or two. I'll get you a part number when I get off duty.
Did a little snooping ... Try 66-75 Bronco
.... and this just showed up on the FordFE.com classifieds http://www.network54.com/Forum/thread?forumid=75943&messageid=1089248213
I got a catalog that lists 10x1/34" drums as being for the follwing apps ... 62/65 Fairlane (Excl Police,HD,Wagon) 66 Fairlane 6cyl,289 Sedan...
Separate names with a comma.