The Jalopy Journal
Was looking for a repop set of 14” stock rims for 1958 impala. Cant seem to find any specific to the 58. I know they make repops for tri5 in 14”...
Anyone know where to buy or who sells this type/ color of caddy like material? I been looking everywhere and no luck
Wondering what is the correct backspacing for the front wheels since the old stock ones will not clear calipers rotors on fatman ultra low msII...
Anyone have pics of chopped 1953 chevy 150 sedan using the stock back glass? Thanks
Was wondering if owners with both 1950 plymouth and 1950 dodge 3 window business coupe could give me a length and width measurement of the rear...
Anyone know If Rob Fortiers 53 chevy chopped by Todd Gravelle Had a 1949 Plymouth back window or 1950 Plymouth back window? Thanks
Off topic but does anyone know quickest way To get a welding Cert In the bay area?
Wondering If could see some pics of front inner wheel wells on 49-54 cars with mustang II, I know it hard to trim out the front inner wheel wells...
Anyone know where I can find blank sbc motor mount fab plates in this type of shape with the ears instead of the triangle type? Thanks [IMG]...
Anyone have any good pics of cars with just outlined only pinstriped flames, preferably looking for cars that are full blown flamed front to...
Was wondering what ppls thoughts would be on a Relocated battery in the trunk along with a mustang gas tank in there also? Im sure it prolly be...
I been lookin for a 23" Gennie Rearmount but looks like noone has these anymore. Anyone know of a place that has any in stock? Thanks
Little off topic but I got an old manley brand floor jack. but dosent seem to hold anymore. Was wondering if there are rebuild kits out there...
I was wondering if it is possible to repair a warped panel when your unable to to get a hammer and dolly in on the back side. I got some slight...
I'm ready to purchase an underdash booster setup for my 54 chevy. I was looking a Krugel components setups. Questions is not sure the size I...
Hey guys, I dont normally ask Airbag questions but need an opinon. Im using 6" slam bags on a severely lowered car. I normally set up the rear...
I was wondering If front drums for the 49-54 chevy are interchangeble? I thought I remember hearing that there was some differences in 52-54...
Anyone know if anyone sells longer square u bolts for 49-54 chevy rear leaf spings. Got old set of lowering blocks i made while back, but dont...
Does anyone know if they make a electric version of a mini angle grinder that can use arbor and 2" and 3" sanding disk? [IMG] Uploaded...
I been encountering few instance where Im trying to weld in tight confined spaces where I cant fit in with my welding mask on to see what Im...
So Im getting ready to 4 link up the rear of my car, With a level at zero on intake and motor set, My tranny is bout 4 degrees down. I think rule...
Curious if Anyone used a 2 piece driveshaft on their bagged cars, any pros cons etc..? Thanks
I know u throw a level on a 4bbl intake to set up ur engine. My question is I set my engine up with a 4bbl manifold with the degree built in to it...
Was wondering what headers you 49-54 chevy guys are running with msII u joint steering. Im running one double D shaft with a one column u joint...
Anyone have a plastic mockup sbc I can borrow or rent for a few days, in need. Thanks phil
So Just got my chevy on the ground to check the stance with the fatman ultra low I installed and new 670's. The Car is low but not as low as I...
Any one know the correct measurement for the rack notch on a fatman ultralow? Thanks
Anyone know where I can find a set of chevy c10 trailing arm brackets? the bushing side brackets that are on the crossmember Thanks
Im pulling the body on my 54 chevy. Was wondering if there is anything special I need to do besides gut the extra inside weight etc... Me and a...
Does Fatman offer builders guides for 49-54 chevy? Somthing that gives reference holes for axle centerline, measurements for my particular car...
Separate names with a comma.