The Jalopy Journal
[ATTACH] [ATTACH] Here is what must be the exact same pilot adapter that is shown in the Hot Rod article that Lou posted. Look at post 17 and...
They are Rochester AA carbs. I have run them since 2016 on a 324, .030" over, mild NOS 49-51 303 Crower Hyd cam which I had to use the 1.5 ratio...
2 and 1/2 years late to provide an answer to the 36 case "definitive differences" . I don't post much, and even though this info would only...
Thanks for posting that, I felt like I was the only one. (Just turned 69) Also, you're correct about better weather and SUN. We finally got...
This is fact ^. I tried Fastenal back in October for shipping from Cal to CT, and they only replied "Thank You for your shipping quote request,...
Hi Carp, here's some dragged out vintage car ramblings.... no way to keep it short,, Last Fall when I fixed the blown out exhaust on the 32 Nash...
As already mentioned above, the 57-58 371 is a totally different design engine compared to the 59-60 371. (The cubic inch is the same because the...
49 and 50 303 used the Rochester AA back draft carb that needed a lower profile distributor cap to clear the huge crossways design air cleaner...
that says 4 amp max or to run more in series. I see this one below that is rated 10 amps, 50 watts continuous use, same price. PM Crazy Steve...
Runtz is for low milliamp draw, like gauges, it won't work on blower motors. Next possible thing that may be mentioned is a vintage underdash...
Yes, still using the 32 as a year round primary car, as the only other registered vehicle here is my 66 Chevy K20 that only goes out maybe 3 times...
I can't do that as it goes deeper...see below: Let me try again to explain how the negative comments, AKA "opinions", affect those that come here...
X2. It happens a lot, and sometimes subtle, sometimes in your face, but it's just the fact they had to post something to feel important?,...
If you don't want to use a new crush sleeve, (which can be a real bitch to get it to start to crush)... Pull the seal and small bearing out, and...
As an Edmunds part, it's unlikely to have any numbers. My Olds Edmunds intake only has a B on the underside, and that might be because it was the...
That's a very cool story on how it survived, and how you obtained it. You did absolutely nothing incorrect by asking for ID help, as it been done...
The large ones are not cowl lights from the 20s-early 30s due to phillips head screws. I've seen those for decades at swaps, and they must have...
There is a thread on here from 2009 that I started, some text & pic below: (Link to the whole thread is below the pic.) 2009>>>"I had some...
I think it's because this site was taken over by 1-800 "assemblers". The guys who only use old stuff like this site was originally about, now...
x2 You must make sure that the linkage puts into 3rd all the way. Then the detent needs to be working. Then it could be worn fork, but likely...
nearing age 68, I've been bummed out since spring, wishing there would be a way to get rid of tons of stuff and a few hopeless project cars. I had...
The Olds rear is around 59.5" flange to flange, so if yours is full fenders, you need a wheel that very shallow dish to keep tires under the...
one more thing I read on here... the hub on the disc sometimes sticks out too far at the trans side, and it gets jambed onto the rearmost ending...
I have read on here about the trans pilot shaft is too long on certain 5 speeds, maybe s10. I never used any of those 5 speeds, so I could be...
2-1/2 pages at one point. If members knew that it only takes 2 people to hit the report button, they get deleted instantly. You don't need to be...
There was a hamb thread on what must be the same collection on ebay about 2-3 years ago.
I'm also from the Northeast salt belt. I know exactly what you describe as medium/serious rust, which is a scaly mess. You would have to needle...
x2, and it's called a Mopar wavy tube axle. I know I helped a friend get one out of a later 30s Plymouth, but I don't know what exact years and...
The 2" perch bosses were only on 32-36. All other years before and after, were the 2-1/4. Being that the 32 "heavy"beam is taller in profile, the...
32 with a taffy drop:cool:
Separate names with a comma.