The Jalopy Journal
Just checking for anyone who has a 33 Willys to see what rear coil over spring rate is working for you .Street driven, SBC, 200/4R fiberglass...
About to remove glass body off, (cab only, tilt front end) and wanted someone that has actually done this if this should be a safe attack at it....
Working on 33 model 77 and wondering if anyone has found a 7/8" disc/disc tandem master cylinder other than Wilwood. Would rather pay $50/$60 than...
Have a new project car, 33 Willys glass car. Not much room for anything,including me. Having a hard time finding a radiator to fit. Yes, I've...
Picked up 33 Willys fiberglass roller lately and looking to find out what headers fit decently. SBC for motor. Like fenderwells but don't know if...
Just picked up 33 willys glass project car (roller) from a guy retiring from hot rodding and having a hard time finding the glass rubber seals for...
Looking at a friends project he bought and has stored for 15+ years and has not did anything to it since. Wondering if anybody is familiar with or...
Finished my 40 plymouth rod project two years ago. I bought the Speedway straight axle kit with the 9 1/4" Mustang ll/Pinto rotors with GM Metric...
Seen a few ideas to wire a PS-64 switch/sender to shut down fuel pump, any reason I just can't run my negative from FP relay to one side of sender...
Put a 350 ho crate motor in my rod project and got it running this spring,have about 750 miles on it so far. Had the 600 vacuum Holley on it, but...
Looking for suggestions on who makes a dependable power window kit for my 40 coupe. Looking at Electric-Life, Specialty, and Balls. They all say...
Just cutting out the inner door panels out of hardboard and so I won't have to do it twice wondering which kind of adhesive/contact cement is the...
On my 40 I semi-polished the aluminum thats on it, dash, firewall, some interior, console, running boards. Any ideas on keeping them looking half...
Been working on this project for about three years now and hope to have it fired up and rolling this spring but just looking for some input about...
Doing a 40 Plymouth coupe project and put these in the car.....Two 7/8 cylinders with equilizing bar on pedal.Wondering if anybody has also used...
Just got body back from being blasted and primed and after Googling what body filler to use, there's alot out there, just got back into this after...
Ready to fire new sbc crate motor, (1996 350 HO vortec) I know it calls for 10-30w but I have 5 quarts of 30 weight break-in oil on the shelf and...
Any reason that I can't run the single wire alternator wire (fused) and/or the main wire going to fuse box to the lug on the starter so I don't...
Slowly getting the axle/ steering set-up mocked in and need some insight from someone who's done it before, this is my first attempt. Everything...
Any ideas out there how much clearance I should have oilpan to tie rods/draglink before I set the engine mounts in chassis. I'm mounting Speedway...
Say, anybody change out the wheel studs for longer ones on these hubs? They say 0.475 knurl needed but that might be the size of the stud hole....
Have'nt been on here for awhile, slowly getting to a rolling chassis. Any ideas or comment about the pics would be appreciated. Found a 8.8 and...
Looking for someone who has installed/assembled Speedway 6" dropped axle kit. (duel leaf) Straight axle kit from them bolts together as kit , but...
Picking up new venture 3500 for great price, (new) wondered if anyone has used on street rod with 350-400 hp motor. Car will be about 2600 lbs....
Looking for some info on fitting more than performance fenderwell headers, $300 or under.Lots of them on ebay for almost too cheap, but would...
Retired lately and got back into cars after about 25 years or so.Have most the stuff to build something now and the time. Picked up a 40 Plymouth...
new here, just got back into cars lately, unreal how much has changed in 25-30 years. the amount of info and pre-built parts is amazing. i've...
Separate names with a comma.