The Jalopy Journal
The magic eraser works awesome, used it for years.
Do you have the accelerator pump rods set on the winter position, I have had the best performance there.
There is a longer style fender bracket near the top o the cowl.
If that's on the pickup, the angled end goes on the fender tab at the bottom just behind the wheel opening and the brace goes straight up and...
Bob Drake sells stainless kick panel retainers and I think Summit also carries them, bought mine in 2022, the headliner retainers I could not find...
Thanks for the info, I think I'll contact Clive at stromberg and see what sizes he thinks are best at our 4000 ft altitude.
Has anyone used these with success , I was trying to figure out how you would get a baseline setting then fine tune from there, thanks for any...
It could be a 43 as the always started the next model year late summer or early fall the year before.
is there any company that makes a early ford 59a style 4 barrel intake without a fan mount,
Also in your first pic at the back of the flat bar to the rear, underneath is a round heavy bar the hook catches on.
It looks like everything you have is correct, if t wont latch it all comes down to hood, grille and fender alignment, some good advise here and on...
So that is correct for the grille brace in the first picture providing all the trim and latch is 41 1/2 ton I just went thru this on my 40 which...
Send a Pic of the hood latch assembly, don't listen to the 42 stuff its a different animal.
You're first pic is correct for the 41 they are the same 6 or 8 the second pic is 40 std and 40 pu The hood mechanism is the big difference ,the...
Most of the 8ba 11 inch flywheels were also drilled for a 10 inch clutch
I have my 47 ford coupe, mild 59a 11Inch clutch with stock 47 trans, it is not hard to push, no problem in traffic for 13 years, only issue if you...
My 47 avatar car has an isky 77b, pretty tame cam, smooth stock idle speed. My 40 Ford pu, 276, dual carb offy heads has a Schneider regind Potvin...
I run champion H 12 plugs [512] they are one heat range hotter and I do that because I run stock jetting on the dual 97s and we are about 3900 ft,...
My dad's 41 chevy sedan had an under seat heater just like that, it worked great.
How do you go about adjusting the proportioning valve, my 40 pickup has underfloor power brakes and 4 wheel discs.
I used Krylon32 kit on my 40 pickup, works fine.
I can send you a measurement from my stock 40 pickup from the firewall lip to the hole if you like, all stock springs and hinges.
Forgot to add on top of the frame.
My 47 is stamped on the drivers side of the frame just behind the front crossmember.
hotrodjack33 was right , found a different listing for 42 to 47 truck and sure enough that was the mirror, 41 to 48 car , just long enough to see...
I have Diamondback wide whites on my 47 coupe, they have been great and I just clean them with water and a Mr Clean magic eraser.
I have a 11 inch clutch in my 59A in my 47coupe, works excellent, however I have a friend that replaced the complete clutch in an original 40 last...
I have a 47 long door coupe that I restored in 2014 , and as I recall the seat tracks holes go right thru the car frame and there is a filler...
I have the same mirror with the stamped mount here, exact match for my 47 car, same length shaft as the oval.
Maybe a silly question did the 40 to 47 trucks have a different interior mirror with a longer shank than the cars, I have a 40 oval mirror and its...
Separate names with a comma.
The Jalopy Journal
