The Jalopy Journal
Instructions on how to post pic's on HAMB
Has anybody come up with a new hood hinge that actually works for 46 to 48 Fords yet?
Have any of you guy's heard the rumor that Santa Maria has been called off for this year as per Covid Instructions . I couldn't find anything on line.
FREE This is a cherry Calif 51 Merc Frame left over after a buddy changed to a later model GM frame. I had 3 Merc's back then and it was given...
Free it was free to me when I had 3 Mercs and I will pass it along to someone who can us it. 619 562 7879 leave a message and I'll get back to you.
I have an old oil stain on my garage floor that doesn't want to go away. I have tried most of Simple Green type cleaners and even tried lacquer to...
Hey guy's. I have a new engine that was recently completely rebuilt but it will be a year or so before it can be installed. Look for advise on how...
Can a master cylinder set up for drum rear and disc fronts be used with a drum/drum system w no problems?
Hey guy's Although I have never had a problem with the old Amp Gauge's I have had in other old Fords I have built. I decided after reading other...
So I have my just completed top bottom restore 46 dash sitting on my bench next to my new American Wire - wire kit. A buddy of mine stopped by...
During a conversation regarding voltage drop for the stock gauges on my 46 Ford I had mentioned that I was going to go with the C & G 3 wire unit...
I know this has been discussed before on the HAMB. But I used the search button and didn't come up with much so I'll bring it up again. I was...
I'm sort of new to the small block Ford part of hot rodding and I'm trying to educate myself with any new info I can absorb. The subject of...
I went to HAMB Search first and couldn't bring up any info on the Eastwood drum type stripping tool for rust and paint. I have watched the videos...
Hey guy's. Just getting ready to put some of the new glass in my 46 and was wondering what the best type of window to rubber sealant builders are...
Just got a 3 door heater for my 46 that has a 302 engine and a Edelbrock intake. The heater is bolted through the lower firewall like stock....
If you have them, please post pics of Santa Maria 2018
Getting ready to have a new drive shaft built and I want to be sure I get it right. I have always been told to push the yoke in the tranny till...
I completely went through my column drop/lock/ign. assembly. Before I put it together I am assuming that the mover parts like the column lock...
Per an earlier post regarding installing a volta drop from 12 to 6 volt for my swap meet 3 door heater I was highly advised to NOT use a volta...
Hey guy's, I picked up a 1946 Ford and 2 speed 6 volt heater. My 46 has a 12 volt system, have any of you guy's used a 12 to 6 volta Drop...
I have a fat fender car with a 302 and C4 w a new aluminum radiator. It has two tranny cooling lines at the bottom tank. I have had two...
Can you guy's in AZ still buy Acrylic Lacquer Paint and thinner? Flat impossible to get in this craze So Cal state I live in. I need to do some...
I thought I might have found something in the HAMB Search regarding my question but couldn't bring it up. I just bought a 46 w SBF and C4 trans...
what is the best product to try and bring back the shine to old Nitro type Lacquer paint.
What is the best way to remove old stripping without effecting the existing paint?
Hey guy's There is a new book that was just released a couple of weeks ago called - San Diego Drag Racing and the Bean Bandits. It shows pics and...
Over the last few years I have seen more Armstrong Lever Shocks being used on Hot Rods but haven't been able to talk with the owners to see how...
Hey guy's, I hope this copy of the parts book comes out OK. Take a look at part # 17794. This is a SS pan that install just under the 49 Merc...
I had asked the HAMB about an Eastwood cutting and didn't get a good review. What would you guy's recommend. A guy was telling me last night...
Separate names with a comma.