The Jalopy Journal
I use mastercoat rust remover/ metal prep with zinc which is the old Captain Lees formula. And then I followed up with the mastercoat permanent...
Greg, A plant sprayer should work , if it doesn't work go to Harbor Freight and get an engine cleaning gun from Taiwan for ten bucks and you can...
There are rust removers that contain zinc and do not require a water rince. I've been treating seams like this and after 20 years with this method...
If you're looking for a coating system to combat salt corrosion this video should help How to PROPERLY Paint Over Rust Part 2 of 2. Applying...
A salt fog test demonstrates that moisture actually penetrated the epoxy primer. a few years ago on another formum someone asked that they had put...
I use rage gold on my projects. The gallon of Bondo I used on my van. Here's the beauty of it once I put down My primer and then any kind of...
[IMG]
Panel number 4 had a large blister in the middle Number two and number six survived the test. These panels will not be rinsed off they will...
Panel number 3 had two coats of epoxy primer, Bondo was applied over it followed by another coat of epoxy primer over the bando. Number four is...
YES
Sorry for the confusion this was going to be a video but I've got tired. Number one is the zinc phosphate epoxy three coats over a slight bit of...
[ATTACH] This is a 28-day salt fog test. I used the Bondo brand body filler on bare metal , over epoxy zinc phosphate primer , and the aluminum...
https://www.fluoramics.com/how-to-construct-an-inexpensive-salt-fog-chamber/
My epoxy primer arrived today TCP zinc phosphate primer. I've noticed a lot of threads about body filler over bare metal over epoxy,over metal...
Ospho is a rust remover and converter and has a good amount of phosphoric acid ,wettng agents and detergent If you leave it on the surface and let...
Hello 41 Helen I think you should be fine. Some epoxies want you to use a prep and some don't. Always consult the product data sheet for the...
If there's no white residue left we should be good to go. Like I said earlier in my post scrub it good to Scotch-Brite pad and plenty of water ....
When you have an excess on the panel of Ospho or any other metal prep re wet the surface with the acid soak a Scotch-Brite pad in water scrub it...
I just ordered some DTM epoxy primer so I can see which way is best. Thanks
Three years ago my daughter's car got T-boned. She came in the house one day and said Daddy! Daddy! I got a big rust spot under my door . I went...
Here's what I would do. I would DA it down with 220 Grit. wipe it down down with wax and grease remover. Apply 2 THIN coats of the sealer over it...
Yes it is a sealer. Only type of sealer that's airtight.
About 20 years ago I got a call from Vintage cars in South Carolina. They were using the silver which was that time Slim. Everybody usually starts...
Imron to the best of my knowledge is a blend. Polyester and acrylic blend. Lay a rag with enamel reducer on it within 10 minutes it will attack it...
Mastercoat Slim solvent proof, goes over any kind of primer and paint, and any kind of paint can go over it. it has a 7-Day window. I have shops...
Avanti I had never idled at the same speed ever. I used to do alot of long-distance travelling and I'm more comfortable with a car that had parts...
I really enjoyed your video. I've driven Avanti 11 for 35 years my first Avanti was it 64 R1 I prefer the Avanti 11 . Small block Chevy is more...
[MEDIA] This discussion has been going on for decades. In the seventies and eighties the cars we did with lacquer...
Intoduce your sandblaster to metal prep. This will prevent flash rusting until you can get a decent primer over it. Primer is to prevent...
Most epoxy putty can be mixed and then by wetting your fingers you can feather edge it out. When you paint your wheel use a two-component...
Separate names with a comma.