The Jalopy Journal
Bought a 1959 Galaxie and the plan was do a full retro custom. Start with upgrading the suppression bag system and disk brakes. So far have not...
Cannot believe the are no 4 link kits for the 1959 Galaxies. Plan was to upgrade to a bagged suspension. How can there be 4 link setups for 1956...
Go with Jetta Mid Nineties model small latch & small locking post bracket for mounting to deck lid. Just picked one for my 29 roadster 12 bucks....
Any info regarding the the torque tube adapter. Is it custom made or did you purchase online, name of source. Have two T5 4X4 & hog head but have...
Appreciate the help 97
Did everyone see the tech article on the MillerHi speed head T5 model A upgrade package in the May issue of Hot Rod Deluxe. Check out the...
Rmak what year is your vehicle 28-29 has a lower gas tank than the 30-31 and you may need to add a fuel electric pump to keep the bowl filled.
Purchased a 32 heavy axle at a swap meet two weeks ago. The axle has on small tapped hole and one cut off embedded spring perch to deal with....
Go with Red lines upgrade by a couple of years
Had a similar problem with Lincoln 100 welder. There is a thermal breaker located between the windings of the transformer with a single lead wire....
Figure 10° of advance per 1000 RPMs. So the most stock A is going to rev is 2800 RPM. With gearing wheel size etc. Normal top 2200 RPM so you...
Just did one in a small heat treat chamber, but sure an oven will work. Heat Assembly up to 450° F. Remove from the oven and use a small dampen...
Picked up a B short block at an estate sale. New babbit crank turned have fresh rods no pistons. Prior to purchasing this set up was working on a...
If you buy the lot like first shot at purchasing the Zepher intake.
Matt, Check out January Banger Thread for Fly Wheel modifications http://www.jalopyjournal.com/forum/showthread.php?t=321363&page=20&highlight=banger
Bulto why screw around making you own rods pistons try this website from Gentleman in Texas F.A.S.T record holder custom parts at your...
While on the subject of compression ratios are 283 Chevy pistons a direct replacement or not in a model A engine. Are there other changes...
These F150 transmission instructions are from a very nice gentleman Al Berry. Al was kind enough to share his retro fit of Transmission to model...
<TABLE class=MsoNormalTable style="WIDTH: 100%; mso-padding-alt: 0in 0in 0in 0in; mso-cellspacing: 0in; mso-table-lspace: 2.25pt;...
29 Roadster on steroids
really Appreciate your support on this matter, have request in to the van Norman web site. seems like they are on holiday call left voice mail,...
Need to deep dive unit, take the units drive head apart. Unit only turns by the drill drive (as noted) go's about three quarters of a turn before...
Need a Custom gear try Dan;s Antique Auto they make custom gears email [email protected]
Here is a set of PIX's of the Van Norman Valve Inserto Seat Cutter. Any operating instructions would be most helpful
there are pilots for Model A and flathead V8 and a selection of smaller diameter pilots. The lead screw on the side will only advance the cutter...
Does anyone have the operating instructions and service parts list for a Van Norman Inserto Valve Seat Cutter. The only type model number found...
Looking for a source for the adapter plate to mount a T-5 to an AA bell housing. at the Kalamazoo Rod Show found a complete kit with the Pedal...
second time the attahment was lost, one more time
Wak53 Flywheel weight reduction dimensionals compilments of Les Andrews. I am still trying to decide myself type of flywheel configuration V8...
Explain the differences. Manufacutured under the same national standards. The cycle application is more servere but relative.
Separate names with a comma.