The Jalopy Journal
I live in Apache Junction Az. Does any one know of a chrome shop close by that does a good job at a reasonable price to chrome a bumper?
When setting up a Holley 94 multi-carbs, with the extended shaft how do you handle the accelerator pump?
Anyone interested in a pair of rear leaf helper springs. They were bought for a 1953 ford. if so, let me know.
This a original ecg carb from a 1955-1957 ford.They are a direct bolt on for a flathead v/8. I am running one my 53 Victoria. It is a very good...
I replaced the original carb on my 53 flathead v/8 with a ecg carb. It idles real good but when I give it the throttle it wants to back fire. Any...
I am looking to convert my radio in my 53 victoria to am-fm. Can anyone tell me who would be a company to do this. What would be the estimate for...
I purchased the trunk side panels from Dennis Carpenter and was wondering if any one has used them. I am confused auto how to mount them. There...
I am looking to upgrade my 1953 ford flathead to dual carbs. I understand that I need to upgrade my distributor. It is still 6 volt pos ground....
I am looking to re-paint my 3 vicky. It was painted with acrylic enamel previously. Would it be better to use the enamel on bc/cc. Which would...
Has anyone installed a usa-630 radio from classiccarstereo in a 1953 ford? If so, did it fit without any modifications? Were you satisfied with...
I have 1953 ford flathead v/8 that I installed power disc brakes on. I have slight hesitation when opening the throttle. I put a timing light on...
I did a front disc brake conversion with power booster. At this point I don't have a lot of pedal. I have bled the system I cannot pump up the...
I am having a problem routing the brake hoses on my disc brake conversion so they won't bind. If I grind a small tit of the brake caliper where...
1954 Pontiac Bumper. Good chrome no rust. Not show chrome, but a great daily...
Here are pictures of a bumper I have. There are extra holes on the edges of the bumper. Does this look familiar to anyone? I would love to...
I am converting my 1953 ford vicky to front disc brakes. What setup would I need to replace my stock master cylinder? Do I need a proportioning valve?
This has been a 4-year labor of love!!!! The engine had not been running for at least 4 years, so my first project was to rebuild the original...
Has anyone had any experience using the port-a-wall whitewalls? How do they look?
On a 53 ford flathead v/8 with dual temp. sensors,what would you recommend as an after market temp. gauge, keeping in mind a reasonable price?
What does anyone know about UPG 12V 7.2AH Replacement Battery for TRIPLITE SM750UNAFTA. It's a sealed lead acid AGM battery that I want use for...
I am looking to change my v/8 flathead over to a electric fuel pump. Do I need to block off the opening where the push rod goes to the cam?
I am planning on shaving my trunk lid on my Victoria. What do you recommend for solenoid to open it?
I am running 6 volt on my 53 Victoria. If I am out and about my battery Goes dead from whatever, can I safely jump it with a 12 volt?
Does anyone know what a 1953 ford front brake drum specs are? width of drum and how much can safely removed when turning them on a lathe? They are...
[ATTACH] [ATTACH] A photo of my progress on my project.
I just finished painting my ride. It is single stage. I have orange peel and was wondering what would be the best way to get rid of it? I have 5...
I have a 53 ford flathead with a single carb. Does anyone know how to install an air cleaner with the bolt down through the middle to a holley two...
e-mail me at [email protected] inner fender is available for an additional $40.00
I need to replace the roof rail seals on my 53 victoria. They are very expensive. Does anyone know if there is a place to get it in bulk and cut...
I am going to spraying my project with Acrylic enamel. What is the recommendation for wet sanding? The paint system is PPG from TCP. Epoxy Primer.
Separate names with a comma.