The Jalopy Journal
I'm replacing my old electronic ignition distributor with a new one piece, I've already marked "top dead center" and removed old distributor. How...
1964 Chevorolet Impala 327ci 350 Auto Tran I will be upgrading my failed Mallory Unilite Electronic Ignition (External Coil), with a ACDelco...
1964 Chevorolet Impala SS 327ci (Rebuilt) 25K Miles 350 Auto Tran AfterMarket Upgrade(s): Edelbrock exhaust manifold, 300 cfm 4bbl carb,...
Chevrolet 1964 Impala 327ci Mallory HEI With the ignition set to the off position, what type of reading should I get on either a voltage meter or...
Chevrolet Impala 1964 327ci Mallory HEI Ignition Problem: Replaced worn Distributor cap, rotor and plug wires, engine starts with no issues then...
I'm replacing my Mallory distributor cap and rotor (Old ones worn out) on a HEI ignition. When I received my new units, my old 8mm Taylor Pro Wire...
I'm interested in purchasing a "spark plug tester" device and in reading about them, I noticed that there are specific units that are designated...
I'm attempting to connect my remote starter, however the "S" terminal is extremely difficult to reach. Is there an alternative way to make the...
I've had no issues in starting my engine the last 4-5 years, then out of the blue, I'm experiencing inconsistent starts. Make: Chevrolet Model:...
I'm preparing to convert my front drum brakes to disk, the back will remain drum for now. I've read that a "dual master cylinder" is in my best...
I'm interested in converting my drum brakes to disk (front-end) and would like options on disk brake kits. I located this company (CPP) Classic...
Just curious, besides allowing the engine cooling flow to start from the engine through the radiator, what other differences, if any, would there...
I'm trouble shooting a problem with blowing a 15 amp fuse on the "brake/lamps" fuse-box slot (with ignition off). Disconnected the entire main...
Any recommendations for buying a "POWER STEERING PULLEY PULLER TOOL"? Specific brands or tool type(s)? Application: Small Block Chevy
I just completed installing a new intake manifold, I'm now re-installing my distributor on my chevy small block. I dropped my distributor back...
After installing a new intake manifold on my 64 chevy small block, I'm ready to drop my distributor back in. Can I just drop the distributor...
I'm replacing my old cracked edelbrock intake manifold with a new edelbrock performer series on my sbc. The new intake must be a little wider,...
Make: Chevrolet Model: Impala SS Year: 1964 Engine: 327 cui This is my first attempt at swapping out a intake manifold and I need a...
What is a good substitute for product "Edelbrock Gasgacinch #9300" which is used to prep the gaskets and head surface prior to install? Is...
I purchased the following intake manifold to replace my old "cracked" one and had a few questions regarding the configuration. The attached pic...
Anyone have any feedback on the "Tuff Stuff" Alternators? http://www.jegs.com/i/Tuff-Stuff/908/7127NC/10002/-1
I'm planning on upgrading my original 55 amp external alternator to a 100 amp internal, this will help carry the additional amp load for my spal...
I've completed installing a SPAL electric 12V fan, when I have the fan hot wire running directly to the "ign fuse box", the fan starts as I...
Are the following resistance readings within the acceptable levels for a Mallory Promaster Coil Part # 29440: Product Suggested Resistance:...
If I disconnect the entire "horn relay" unit/wire(s)/harness (including the "Bat" wire from the relay to the battery) will it prevent the...
Previous upgraded from stock distributor to HEI system with ballast, engine has been starting and running fine. Question: Is it normal for the...
Hello! User name is 64impala, I own a 1964 Impala SS, I'm having some electrical issues and submitted a separate post on the details! I'm...
What type of analysis or trouble shooting can I apply to the following problem: Make: Chevrolet Model: Impala SS Year: 1964 Engine: 327...
Separate names with a comma.