The Jalopy Journal
You should just get a nice camper and get a Porta potty for in the closet. If that's not good enough, I've seen campers as small as a Shasta...
Ok, gotcha! I've had 2 vintage campers with a factory bathroom. The first was my 1962 Shasta deluxe (19'). They are kinda rare but they do come up...
Most small canned hams will sleep 2 adults just fine. Much more than that gets tough... you may want to look for a Shasta compact, Serro Scotty,...
[IMG] I ended up dragging another one home... its hard to resist when the price is reasonable. Sent from my SM-G900R4 using The H.A.M.B. mobile app
Thank you Sent from my SM-G900R4 using The H.A.M.B. mobile app
I keep getting an error page when I click on the link... do I have to have a membership? Sent from my SM-G900R4 using The H.A.M.B. mobile app
So is there a canvas top that goes over that? I'm intrigued?! Sent from my SM-G900R4 using The H.A.M.B. mobile app
You can get the weatherstrip for sliders from steele rubber. http://www.steelerubber.com/rear-sliding-qrt-window-70-3707-77 Sliding window...
Symco weekender in symco wisconsin. Sent from my SM-G900R4 using The H.A.M.B. mobile app
It was a good show! Glad my piece of junk made it there and back. Sent from my SM-G900R4 using The H.A.M.B. mobile app
[IMG] [IMG] Sent from my SM-G900R4 using The H.A.M.B. mobile app
Also, some pictures from the event.[IMG] [IMG] [IMG] [IMG] Sent from my SM-G900R4 using The H.A.M.B. mobile app
[IMG] [IMG] This is my setup for symco this year... Sent from my SM-G900R4 using The H.A.M.B. mobile app
Thanks man. I decided to take a victory lap through downtown. I was just looking through your instagram and I found a picture of my truck from...
[IMG] Just wanted to finally add a good picture of my truck! Sent from my SM-G900R4 using The H.A.M.B. mobile app
[IMG] Finally got the new AA harness in my hands and installed. It was so nice to work with. Anyways... back on the road with the Pertronix 2...
[IMG] [IMG] Here is my gem top. I screwed an awning rail to it so I could use my awning. Sent from my SM-G900R4 using The H.A.M.B. mobile app
I have seen them too, but maybe not always same day availability... I'm am confident in the pertronix modules, I know a lot of people using them...
Yes. 100% sure. I took it to my friends shop where they specialize in rebuilding starters and alternators. We put it on his test machine,...
I tried grounding the alternator better and switched back to point/resistor wire. I'm still cooking that 30 amp fuse. I got so frustrated I bought...
Thanks. Here is another pic from torquefest[IMG] Sent from my SM-G900R4 using The H.A.M.B. mobile app
I have my alternator grounded to the core support. I'm going to ground it to the engine now that you've said that. I don't know if I'm capable of...
Yes, I meant internal.
I'm also going to switch to a different ignition switch out of a parts truck. The switch I've been using is not original, it says made in mexico...
I'm going to unplug the gauge and run points for a bit to see what happens. Sent from my SM-G900R4 using The H.A.M.B. mobile app
It is the stock gauge, so not much... a factory generator doesn't put out much. Sent from my SM-G900R4 using The H.A.M.B. mobile app
They told me over the phone to keep it wired to straight 12 v. They said the ignitor 2 can handle uo to 16v? Sent from my SM-G900R4 using The...
Ok, so I should leave the resistor wire? I have the ignitor 2 and the 0.6 ohm coil. They are sending me a new ignitor 2 module through warranty....
I have the wire from the starter disconnected. The wire to the coil comes right off the fuse block. Sent from my SM-G900R4 using The H.A.M.B....
I would rather go that route, but there is no room and my engine compartment is finished out rather nicely to go beating it in with a hammer....
Separate names with a comma.